Plaquette en carbure carrée pour gouge à dégrossir 11 mm
Le Belmash RS-02 est inestimable pour travailler avec des pièces de bois plus longues que ce que la table de travail peut supporter. Ce support à rouleaux offre un moyen sûr et facile de travailler avec ces pièces surdimensionnées. Facile et pratique à utiliser. Equipé de rouleaux en téflon pour éviter d'endommager votre pièce. Hauteur réglable entre 700mm et 1050mm.
UITVERKOOP
Economy -systeem REKORD : 14-delige set Kozijn-frezen
Uniek voor de productie van kozijnen, ramen en deuren volgens de Nederlandse standaard profielen.
Asgat 40 mm.
rekord raamfrees nr 128 1,00
rekord raamfrees nr 999 1,00
rekord raamfrees nr 918 1,00
rekord raamfrees nr 921 1,00
rekord raamfrees nr 922 1,00
rekord raamfrees nr 938 1,00
rekord raamfrees nr 916a 2,00
geslepen freesdoornring d40x21.5 1,00
geslepen freesdoornring d40x17.0 1,00
geslepen freesdoornring d40x14.0 1,00
geslepen freesdoornring d40x9.5 2,00
geslepen freesdoornring d40x9.0 1,00
Le Belmash RS-01 est inestimable pour travailler avec des pièces de bois plus longues que ce que la table de travail peut supporter. Ce support à rouleaux offre un moyen sûr et facile de travailler avec ces pièces surdimensionnées. Facile et pratique à utiliser. Equipé de rouleaux en téflon pour éviter d'endommager votre pièce. Les deux côtés du support peuvent s'incliner de 45°. Hauteur réglable entre 700mm et 1050mm.
Set profielmessen hoogte 40mm Nr. 0036 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Sortie optionelle 2x Ø125mm pour utilisation avec Air Flux Cyclone. Le grand diamètre est de 203mm, directement connectable aux groupes d'extraction du cyclone Air Flux, avec des branches 2x125mm.
Universal saw blade with alternate top bevel teeth for cutting of different types of wood, laminated materials, double sided veneer panels or particle board in stack. For panel sizing machines and table saws. Available with different number of teeth.
Groeffrees met omkeerbare messen en voorsnijders in hoogwaardig hardmetaal (HW) voor het maken van dunne precisiegroeven. Instelbaar in hoogte tussen 8mm en 15mm door middel van afstandsringen. Afstandsringen standaard inbegrepen. Dankzij de hardmetalen messen snijdt deze groeffrees moeiteloos door massieve platen, harde en zachte houtsoorten, MDF of gelamineerde platen.
Verkrijgbaar met asgat 30mm of 50mm.
This bit is made specifically for machining dovetail joints. Dovetail joints are classic, but extremely strong, mechanical connections to be used in general woodworking. Use these joints to construct cabinet drawers, coffins, cases, or other types of furniture. Thanks to the hard metal (carbide) cutting edges, a clean and accurate result of all your milling and woodworking projects is guaranteed.
To work even faster or more efficiently, it is possible to use a dovetail-mold.
Cutterset consisting of two elements in light alloy with reversible tungsten carbide knives (HW). Cutter set specifically designed to perform both high precision planing and chamfering. Suitable for machining wood with a height between 18mm and 50mm. The blades have a radius on the one hand and a chamfer of 45° on the other hand. The blades with radius R4 are mounted on the milling head as standard. Knives with radius R2, R3, R5 and R6 are available separately.
Because the knives are placed both above and below the cutterset, it is possible to round off/chamfer your workpiece in one passage. Thanks to the tungsten carbide blades, this profile cutter cuts effortlessly through solid boards or solid wood. Also suitable for use on sheet materials.
Set profielmessen hoogte 40mm Nr. 0055 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
De standaard veerschuimen zijn geschikt voor de FeatherPRO en FeatherDUO veerklemmen. Ze hebben dikkere scharnieren t.o.v. de ultralight kammen om meer kracht te hebben bij hogere druk. Set van 2 stuks.
Ce rabot ponceur de Virutex est facile à utiliser et donne des résultats rapides et efficaces sur de grandes surfaces. La machine donne d'excellents résultats sur toute surface recouverte de peinture, de résine, de vernis ou de panneaux stratifiés. Facile à utiliser sur différentes surfaces telles que le bois (également contre le grain) ou les panneaux sandwich. Un manchon ponceur avec un rouleau abrasif de grain 50 est monté en standard. Des manchon ponceur avec différentes grain sont disponibles sur demande. Aucun outil supplémentaire n'est nécessaire pour remplacer les manchon ponceur.
Standard livré dans un étui pratique en PVC.
Dubbele zuignap die flexibel met elkaar verbonden zijn. De zuignappen kunnen dus bewegen tegen over elkaar. Sterk plastic body uit ABS. Inclusief beschermende cover. Deze zuignap heeft een laadcapaciteit van 30 kg.
Cutter head in light alloy with blades in high quality tungsten carbide (HW) for machining of quarter rounds. The set comes deliverd in a plastic box. With standard delivery the knives of radius 5/10 are mounted on the body. The knives of radius R3/6 and R4/8 are supplied within the box. Thanks to the tungsten carbide blades, this grooving cutter cuts effortlessly through solid boards or solid woods. Also suitable for use with plywood or chipboard.
Available with bore 30mm or 50mm.
Content
Plaquette en carbure carrée pour gouge à dégrossir 11 mm
Le Belmash RS-02 est inestimable pour travailler avec des pièces de bois plus longues que ce que la table de travail peut supporter. Ce support à rouleaux offre un moyen sûr et facile de travailler avec ces pièces surdimensionnées. Facile et pratique à utiliser. Equipé de rouleaux en téflon pour éviter d'endommager votre pièce. Hauteur réglable entre 700mm et 1050mm.
Economy -systeem REKORD : 14-delige set Kozijn-frezen
Uniek voor de productie van kozijnen, ramen en deuren volgens de Nederlandse standaard profielen.
rekord raamfrees nr 128 1,00
rekord raamfrees nr 999 1,00
rekord raamfrees nr 918 1,00
rekord raamfrees nr 921 1,00
rekord raamfrees nr 922 1,00
rekord raamfrees nr 938 1,00
rekord raamfrees nr 916a 2,00
geslepen freesdoornring d40x21.5 1,00
geslepen freesdoornring d40x17.0 1,00
geslepen freesdoornring d40x14.0 1,00
geslepen freesdoornring d40x9.5 2,00
geslepen freesdoornring d40x9.0 1,00
Le Belmash RS-01 est inestimable pour travailler avec des pièces de bois plus longues que ce que la table de travail peut supporter. Ce support à rouleaux offre un moyen sûr et facile de travailler avec ces pièces surdimensionnées. Facile et pratique à utiliser. Equipé de rouleaux en téflon pour éviter d'endommager votre pièce. Les deux côtés du support peuvent s'incliner de 45°. Hauteur réglable entre 700mm et 1050mm.
Set profielmessen hoogte 40mm Nr. 0036 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Sortie optionelle 2x Ø125mm pour utilisation avec Air Flux Cyclone. Le grand diamètre est de 203mm, directement connectable aux groupes d'extraction du cyclone Air Flux, avec des branches 2x125mm.
Universal saw blade with alternate top bevel teeth for cutting of different types of wood, laminated materials, MDF, double sided veneer panels or particle board in stack. For panel sizing machines and tabel saws. Make sure to use the right amount of teeth to achieve optimal results of your project. A low number of teeth is suited for fast-paced and rough sawing. A high number of teeth calls for a lower operating speed but guarantees a clean cut. Available with different number of teeth.
Groeffrees met omkeerbare messen en voorsnijders in hoogwaardig hardmetaal (HW) voor het maken van dunne precisiegroeven. Instelbaar in hoogte tussen 8mm en 15mm door middel van afstandsringen. Afstandsringen standaard inbegrepen. Dankzij de hardmetalen messen snijdt deze groeffrees moeiteloos door massieve platen, harde en zachte houtsoorten, MDF of gelamineerde platen.
Verkrijgbaar met asgat 30mm of 50mm.
This bit is made specifically for machining dovetail joints. Dovetail joints are classic, but extremely strong, mechanical connections to be used in general woodworking. Use these joints to construct cabinet drawers, coffins, cases, or other types of furniture. Thanks to the hard metal (carbide) cutting edges, a clean and accurate result of all your milling and woodworking projects is guaranteed.
To work even faster or more efficiently, it is possible to use a dovetail-mold.
Cutterset consisting of two elements in light alloy with reversible tungsten carbide knives (HW). Cutter set specifically designed to perform both high precision planing and chamfering. Suitable for machining wood with a height between 18mm and 50mm. The blades have a radius on the one hand and a chamfer of 45° on the other hand. The blades with radius R4 are mounted on the milling head as standard. Knives with radius R2, R3, R5 and R6 are available separately.
Because the knives are placed both above and below the cutterset, it is possible to round off/chamfer your workpiece in one passage. Thanks to the tungsten carbide blades, this profile cutter cuts effortlessly through solid boards or solid wood. Also suitable for use on sheet materials.
Available with bore 30mm or 50mm.
Set profielmessen hoogte 40mm Nr. 0055 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
De standaard veerschuimen zijn geschikt voor de FeatherPRO en FeatherDUO veerklemmen. Ze hebben dikkere scharnieren t.o.v. de ultralight kammen om meer kracht te hebben bij hogere druk. Set van 2 stuks.
Ce rabot ponceur de Virutex est facile à utiliser et donne des résultats rapides et efficaces sur de grandes surfaces. La machine donne d'excellents résultats sur toute surface recouverte de peinture, de résine, de vernis ou de panneaux stratifiés. Facile à utiliser sur différentes surfaces telles que le bois (également contre le grain) ou les panneaux sandwich. Un manchon ponceur avec un rouleau abrasif de grain 50 est monté en standard. Des manchon ponceur avec différentes grain sont disponibles sur demande. Aucun outil supplémentaire n'est nécessaire pour remplacer les manchon ponceur.
Standard livré dans un étui pratique en PVC.
Dubbele zuignap die flexibel met elkaar verbonden zijn. De zuignappen kunnen dus bewegen tegen over elkaar. Sterk plastic body uit ABS. Inclusief beschermende cover. Deze zuignap heeft een laadcapaciteit van 30 kg.
Cutter head in light alloy with blades in high quality tungsten carbide (HW) for machining of quarter rounds. The set comes deliverd in a plastic box. With standard delivery the knives of radius 5/10 are mounted on the body. The knives of radius R3/6 and R4/8 are supplied within the box. Thanks to the tungsten carbide blades, this grooving cutter cuts effortlessly through solid boards or solid woods. Also suitable for use with plywood or chipboard.
Available with bore 30mm or 50mm.
Weight
ND
5,2 kg
28 kg
6,3 kg
0,05 kg
2 kg
1 kg
1 kg
0,05 kg
1 kg
0,05 kg
0,5 kg
3,2 kg
0,6 kg
1 kg
Dimensions
ND
ND
ND
ND
0,4 cm
ND
ND
ND
ND
ND
0,4 cm
ND
ND
ND
ND
Additional information
Poids
5,2 kg
Capacité de charge
50kg
Hauteur
700-1050mm
Base
475x490mm
Poids
28 kg
Poids
6,3 kg
Capacité de charge
80kg
Hauteur
700-1050mm
Base
570x650mm
Poids
0,05 kg
Dimensions
0,4 cm
Poids
2 kg
Poids
1 kg
Diamètre lame de scie
400mm
Diamètre de l\' arbre
30 mm
Epaisseur dent
4,0mm
Epaisseur lame de scie
2,8mm
nombre de dents
120, 48, 60, 80, 96
Orifices de traction
PH02
Poids
1 kg
Diamètre
160mm
Diamètre de l\' arbre
30 mm, 50 mm
Faces de coupe
4
nombre de dents
4
Longeur de coupe
30mm
Hauteur de rainure
8-15mm
RPM Min-Max
4800-8200
Poids
0,05 kg
Diamètre
12,7mm
Longeur de coupe
13mm
Longueur
49mm
Angle
14°
Faces de coupe
2
Poids
1 kg
Diamètre
139mm
Diamètre de l\' arbre
30 mm, 50 mm
Hauteur de rainure
18-50mm
Faces de coupe
2+2+2
Rayon
R4
Angle
45°
RPM Min-Max
5500-9400
Poids
0,05 kg
Dimensions
0,4 cm
Poids
0,5 kg
Poids
3,2 kg
Puissance
700W
Profondeur de ponçage
0-1mm
Largeur manchon ponceur
81mm
Vitesse à vide
16500rpm
Poids
0,6 kg
Supporte
30kg
Diamètre
11,7cm
Poids
1 kg
Diamètre
128mm
Diamètre de l\' arbre
30 mm, 50 mm
Faces de coupe
2
Hauteur de rainure
30mm
Rayon
R3/6, R4/8, R5/10
RPM Min-Max
5900-9700
Abonnez-vous pour notre bulletin d'information
Select the fields to be shown. Others will be hidden. Drag and drop to rearrange the order.
Image
SKU
Rating
Price
Stock
Availability
Add to cart
Description
Content
Weight
Dimensions
Additional information
Click outside to hide the comparison bar
Comparer
Nous utilisons des cookies pour nous assurer que notre site Web fonctionne aussi bien que possible. Si vous continuez à utiliser ce site Web, nous supposons que cela vous convient.OkPrivacy policy