MODÈLE D'EXPOSITION - NOUVEAU
La ponceuse TT1220 peut être utilisée verticalement, horizontalement ou à n'importe quel angle. La grande table en aluminium peut être inclinée jusqu'à 45° et est équipée d'un rapporteur.
De decoupeerzaag is, dankzij zijn fijne zaagblad, uitermate geschikt om willekeurige vormen uit plaatmateriaal te zagen. De voetplaat kan ingesteld worden onder een hoek van maximaal 45°, onder versterk zagen is mogelijk met dit toestel. Het wendbare karakter van dit toestel zorgt ervoor dat het geschikt is voor een fijne afwerking. Het toestel kan gebruikt worden in hout, kunststof, keramiek en hard aluminium. De benodigde zaagbladen worden meegeleverd.
La fraise à rayon convexe de Sistemi Klein est parfaite pour usiner les bords des armoires, des portes et des tiroirs ou des colonnes. À l'aide de cette fraise, créez des rainures de quart de rond sur la plupart des types de bois.
Equipé d'un roulement à billes pour faciliter le travail. Si vous utilisez une fraise de grand diamètre, il est conseillé d'effectuer l'usinage en plusieurs étapes.
Promo pack for milling table Mini Spindle TT40AL
Schuurband voor schuurmachine TT915 - 915 x 100 mm
Showroommodel
Slechts één stuk beschikbaar!
Draagbare kantenlijmer PEB250+ gemonteerd in een uitschuifbare tafel voor het stationair verwerken van grotere stukken. Deze kantenlijmer met lijmbak lijmt probleemloos PVC, ABS, melamine of houtkanten op rechte, ronde of gevormde panelen. De machine is geschikt voor het verwerken van een kantenband met dikte tussen 0,4-3mm en 10-62mm hoogte. Het model PEB250+ beschikt over een snelheids- en temperatuurregeling. Tafel voorzien van houder voor rollen en automatische eindknipper.
De kantenlijmer PEB250TA is net zoals alle andere Virutex modellen voorzien van een gepatenteerde Teflon®-gecoate lijmbak. Deze coating biedt enkele erg belangrijke voordelen ten opzichte van vergelijkbare machines. Na gebruik is het erg eenvoudig om de lijmbak opnieuw schoon te maken waardoor deze kantenlijmer veel onderhoudsvriendelijker is.
Afsluitschuif met muurbevestiging, diameter 100mm om te gebruiken in combinatie met de Air Flux stofafzuigingssystemen.
Set profielmessen hoogte 40mm Nr. 0080 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Bandsaw blade with length 4670mm for use on the TT50BS or TT61BS band saw machine from Tendotools. This saw blade has 4 TPI (teeth per inch) and has a width of 20mm. This bandsaw blade in tempered steel "Flexback" is very suitable for multipurpose sawing. Use this saw ribbon for both wood and plastics. The teeth of the saw blade were given an additional heat treatment for increased hardness. This keeps the band very supple and increases your cutting comfort thanks to the hardness of the teeth.
Specially designed hand gluer for gluing large surfaces with vinyl (white) adhesives. Available in two models with different roll widths and glue container capacities. Model EM26D is equipped with a roll with a width of 122mm and a capacity of 1kg. The larger model EM126D has a roll with a width of 180mm and a capacity of 1.4kg. The machine is equipped with a trigger on the handle for easy opening and closing of the glue container.
Attention: this hand gluer comes standard with a rubber roller, suitable for vinyl (white) adhesives and water-based adhesives. For synthetic adhesives an optional PU roll is available (Ref. 2504065). This hand gluer is also available with an additional adhesive roller at the top for stationary gluing of workpieces from above (models EM25D and EM125T).
Tête mobile avec frein antidérapant pour le PIHER Mod. K serre-joints.
Equipé d'un filetage protégé.
This transport handle is standard equipped with a clamp which makes this handle suitable for multiple functions. Can be used as an edge press, corner press or transport handle. Thanks to its aluminium design, this handle is very strong and robust. The maximum load is 70kg. As an edge press you can use the PC81U on straight panels as well as concave or convex panels. As a corner press, this handle becomes the ideal tool for making frames, for example. The clamp is detachable and by changing the position of the handle, the PC81U can easily be converted into a transport handle. Suitable for panels between 0mm and 46mm thick.
Dernières pièces !
De ADAMIK VC-5 is een dubbelzijdige zuignap die je eenvoudig op de werkbank drukt. Grâce à cette technologie, il est facile de modifier les dimensions de la surface usinée. La ventouse VC-5 est conçue pour serrer des pièces non poreuses pendant le banderolage, le fraisage, la coupe, le meulage, le perçage, etc.
Le grand avantage de la ventouse VC-5 est la méthode de création d'un vide à l'aide du système Venturi, qui comprime la pièce à l'aide de l'air comprimé d'un compresseur conventionnel.
La ventouse peut être utilisée aussi bien horizontalement que verticalement.
Fraises à rainurer sont spécifiquement conçue pour faire des rainures dans des types de bois différents ou des plastiques. Grâce au face de coupe supplémentaire en bout de fraise (Z=2+1), c'est aussi possible de facilement faire de perçage. Ces fraises sont fournis de faces de coupe en carbide. Grâce à ces faces de coupe en carbide le fraise vous assure un résultat parfait de tous votre projets ét une longue durée de vie.
Ce fraise peut être utiliser avec le plupart de types de bois. Grâce a la qualité extraordinaire il est aussi possible d'utiliser les fraises sur les plastiques comme l'acrylat (Plexiglas), polycarbonate, polypropylène ou de PVC. A utiliser dans des défonceuses ou des machines CNC.
SALES
With this edge router, you have affordable automation. Large adjustable carrier plate covered with Teflon carriers. You mill the side, corner and top in one movement from right to left.
Klein® trimming bits with straight cut are suitable for smooth and well-finished edges on melamine and veneered panels. The ball bearing, having the same diameter of the cutters, trims any overlap leaving a flat and smooth edge. Two flutes provide fast cutting and good chipping ejection.
Complete set in wooden box, corrosion-resistant design (gold-bicromat) with a handy sprocket wrench and 4 sets of chucks.
Straight router bits are specifically designed for making grooves in most types of wood or several plastics. Together with two straight cutting edges, there is a special tip on the bottom (Z=2+1) which allows easy and precise boring. This router bit can be used to work on most wood types or plastics. Thanks to the high quality finish of the bit, it is also possible to make grooves on different plastics such as acrylics (plexiglass), polycarbonate, polypropylene or PVC. To be used in router milling machines or CNC machines.
Content
La ponceuse TT1220 peut être utilisée verticalement, horizontalement ou à n'importe quel angle. La grande table en aluminium peut être inclinée jusqu'à 45° et est équipée d'un rapporteur. La table de travail est supportée des deux côtés pour une utilisation de précision. Elle est équipée d'une poignée en D pour un transport facile et d'un système de bande à poncer à serrage rapide pour des changements rapides. La bande peut être facilement équilibrée grâce à la molette très pratique. La machine dispose également d'une buse d'aspiration de 60 mm.
Cette ponceuse est livrée par défaut avec une bande et un disque à poncer avec un grain 80. Les grains 60, 100, 120 et 150 sont également disponibles pour le disque. Les grains 60, 100, 120, 150 et 220 sont également disponibles pour le disque.
Peut être utilisée universellement pour le ponçage des arêtes, des surfaces et des arrondis.
De decoupeerzaag is, dankzij zijn fijne zaagblad, uitermate geschikt om willekeurige vormen uit plaatmateriaal te zagen. De voetplaat kan ingesteld worden onder een hoek van maximaal 45°, onder versterk zagen is mogelijk met dit toestel. Het wendbare karakter van dit toestel zorgt ervoor dat het geschikt is voor een fijne afwerking. Het toestel kan gebruikt worden in hout, kunststof, keramiek en hard aluminium. De benodigde zaagbladen worden meegeleverd.
La fraise à rayon convexe de Sistemi Klein est parfaite pour usiner les bords des armoires, des portes et des tiroirs ou des colonnes. À l'aide de cette fraise, créez des rainures de quart de rond sur la plupart des types de bois.
Equipé d'un roulement à billes pour faciliter le travail. Si vous utilisez une fraise de grand diamètre, il est conseillé d'effectuer l'usinage en plusieurs étapes.
Promo pack for milling table Mini Spindle TT40AL, comprising:
Milling table Mini Spindle TT40AL
Featherboard kit
Kit of 6 routers
Schuurband voor schuurmachine TT915.
915 x 100 mm
Verkrijgbaar in korrel 40 - 60 - 80 - 100 - 120 - 150
Deze schuurband kan gebruikt worden voor het ontbramen en schuren van staal, aluminium, non-ferromaterialen, hout en kunststof.
Draagbare kantenlijmer PEB250+ gemonteerd in een uitschuifbare tafel voor het stationair verwerken van grotere stukken. Deze kantenlijmer met lijmbak lijmt probleemloos PVC, ABS, melamine of houtkanten op rechte, ronde of gevormde panelen. De machine is geschikt voor het verwerken van een kantenband met dikte tussen 0,4-3mm en 10-62mm hoogte. De automatische rollers en aanvoer met geleidersysteem zorgen ervoor dat de kantenband altijd correct op uw paneel komt. Met behulp van de millimeterregeling is de hoogte en dikte van de kantenband erg eenvoudig in te stellen. Tenslotte beschikt de machine ook over een regelbare dosering van de lijm zodat u steeds de juiste hoeveelheid voor uw werkstuk gebruikt.
Bij de draagbare kantelijmer PEB250+ kan zowel de snelheid van de rollers, als de temperatuur geregeld worden. Hierdoor is de PEB250+ erg geschikt om te werken op gevormde panelen. De snelheidsregeling stelt u in staat om altijd de correcte snelheid in functie van het werk te gebruiken. Deze functie biedt op gevormde panelen een groter werkcomfort. De tafel is voorzien van een houder voor rollen en automatische eindknipper. De kantenlijmer kan gemakkelijk uit de tafel genomen worden om mobiel te werken. In dat geval moet u gebruik maken van voorgesneden kantenbanden.
Gepatenteerde lijmbak
De kantenlijmer PEB200TRC of PEB250TRC is net zoals alle andere Virutex modellen voorzien van een gepatenteerde Teflon®-gecoate lijmbak. Deze coating biedt enkele erg belangrijke voordelen ten opzichte van vergelijkbare machines. Na gebruik is het erg eenvoudig om de lijmbak opnieuw schoon te maken waardoor deze kantenlijmer veel onderhoudsvriendelijker is. Daarbovenop betekent dit ook dat u snel en zonder problemen andere lijmen kan gebruiken. Er zijn geen bijkomende aanpassingen nodig om tussen twee projecten te veranderen van lijmkleur. De lijmrollen kregen een polymerisatiebehandeling om beschadigingen aan uw kantenbanden te voorkomen.
Afsluitschuif met muurbevestiging, diameter 100mm om te gebruiken in combinatie met de Air Flux stofafzuigingssystemen.
Set profielmessen hoogte 40mm Nr. 0080 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Bandsaw blade with length 4670mm for use on the TT50BS or TT61BS band saw machine from Tendotools. This saw blade has 4 TPI (teeth per inch) and has a width of 20mm. This bandsaw blade in tempered steel "Flexback" is very suitable for multipurpose sawing. Use this saw ribbon for both wood and plastics. The teeth of the saw blade were given an additional heat treatment for increased hardness. This keeps the band very supple and increases your cutting comfort thanks to the hardness of the teeth.
Specially designed hand gluer for gluing large surfaces with vinyl (white) adhesives. Available in two models with different roll widths and glue container capacities. Model EM26D is equipped with a roll with a width of 122mm and a capacity of 1kg. The larger model EM126D has a roll with a width of 180mm and a capacity of 1.4kg. The machine is equipped with a trigger on the handle for easy opening and closing of the glue container. Simply press the trigger to run the glue over the roll. Using this trigger you will always obtain the right amount of glue for your project. Thanks to the support, the hand gluer can easily be put away. For cleaning, you can keep this adhesive under water without risk of damage.
Attention: this adhesive comes standard with a rubber roller, suitable for vinyl adhesives and water-based adhesives. For synthetic adhesives an optional PU roll is available (Ref. 2504065). This hand gluer is also available with an additional adhesive roller at the top for stationary gluing of workpieces from above (models EM25D and EM125T).
Tête mobile avec frein antidérapant pour le PIHER Mod. K serre-joints.
Equipé d'un filetage protégé.
This transport handle is standard equipped with a clamp which makes this handle suitable for multiple functions. Can be used as an edge press, corner press or transport handle. Thanks to its aluminium design, this handle is very strong and robust. The maximum load is 70kg. As an edge press you can use the PC81U on straight panels as well as concave or convex panels. As a corner press, this handle becomes the ideal tool for making frames, for example. The clamp is detachable and by changing the position of the handle, the PC81U can easily be converted into a transport handle. Suitable for panels between 0mm and 46mm thick.
La ventouse ADAMIK VC-5 est une ventouse double face qui se fixe à l'établi par simple pression. Grâce à cette technologie, il est facile de modifier les dimensions de la surface usinée. La ventouse VC-5 est conçue pour serrer des pièces non poreuses pendant le banderolage, le fraisage, la coupe, le meulage, le perçage, etc.
Le grand avantage de la ventouse VC-5 est la méthode de création d'un vide à l'aide du système Venturi, qui comprime la pièce à l'aide de l'air comprimé d'un compresseur conventionnel.
La ventouse peut être utilisée aussi bien horizontalement que verticalement.
Fraises à rainurer sont spécifiquement conçue pour faire des rainures dans des types de bois différents ou des plastiques. Grâce au face de coupe supplémentaire en bout de fraise (Z=2+1), c'est aussi possible de facilement faire de perçage. Ces fraises sont fournis de faces de coupe en carbide. Grâce à ces faces de coupe en carbide le fraise vous assure un résultat parfait de tous votre projets ét une longue durée de vie.
Ce fraise peut être utiliser avec le plupart de types de bois. Grâce a la qualité extraordinaire il est aussi possible d'utiliser les fraises sur les plastiques comme l'acrylat (Plexiglas), polycarbonate, polypropylène ou de PVC. A utiliser dans des défonceuses ou des machines CNC.
With this edge router, you have affordable automation. Large adjustable carrier plate covered with Teflon carriers. You mill the side, corner and top in one movement from right to left.
Klein® trimming bits with straight cut are suitable for smooth and well-finished edges on melamine and veneered panels. The ball bearing, having the same diameter of the cutters, trims any overlap leaving a flat and smooth edge. Two flutes provide fast cutting and good chipping ejection.
Complete set in wooden box, corrosion-resistant design (gold-bicromat) Comes with a handy sprocket wrench and 4 sets of chucks.
All chucks are equipped with bonding grooves on the inside and outside. Equipped with index plate, quick-release center and screw feed.
Straight router bits are specifically designed for making grooves in most types of wood or several plastics. Together with two straight cutting edges, there is a special tip on the bottom (Z=2+1) which allows easy and precise boring. The router bit is solid carbide, with special micrograin finishing for best performance. Thanks to these combined qualities the router bit delivers high quality results for all your projects and a long working life. This router bit can be used to work on most wood types or plastics. Thanks to the high quality finish of the bit, it is also possible to make grooves on different plastics such as acrylics (plexiglass), polycarbonate, polypropylene or PVC. To be used in router milling machines or CNC machines.
Weight
50 kg
3 kg
0,05 kg
20 kg
0,05 kg
30 kg
0,5 kg
0,05 kg
0,5 kg
2 kg
1 kg
0,65 kg
0,325 kg
0,05 kg
15 kg
0,05 kg
ND
0,05 kg
Dimensions
ND
ND
ND
ND
ND
ND
ND
0,4 cm
ND
ND
ND
ND
16 × 20 × 2,2 cm
ND
ND
ND
ND
ND
Additional information
Poids
50 kg
Inclinaison
45°
Puissance
750W
Grain
K60, K80, K100, K120, K220, 150
Table de travail
200 x 335 mm
Disque
255 mm
Bande à poncer
1250 x 150 mm
Poids
3 kg
Puissance
550W
onbelast toerental
300 – 3200 tpm
slaglengte
26mm
schuine hoek
0° 15° 30° 45°
materialen
hout 80 mm
staal 5 mm
non ferro metalen 20 mm
hard aluminium 15 mm
keramiek 10 mm
Poids
0,05 kg
Diamètre
41mm
Longeur de coupe
18mm
Longueur
65mm
Rayon
R16
Queue
12mm
Faces de coupe
2
Poids
20 kg
Poids
0,05 kg
Grain
K40, K60, K80, K100, K120, 150
Poids
30 kg
Puissance
830W
Inhoud lijmbak
230cm³
Temperatuur (regelbaar)
120 – 200°C
Werksnelheid (regelbaar)
2-6m/min
Min-Max. hoogte band
10-62mm
Min-Max. dikte band
0.4-3mm
Poids
0,5 kg
Diamètre
100mm
Poids
0,05 kg
Dimensions
0,4 cm
Poids
0,5 kg
Longueur
4670mm
Largeur
20mm
Dikte
0,80mm
Poids
2 kg
Breedte lijmrol
122mm, 180mm
Inhoud lijmbak
1kg, 1,4kg
Poids
1 kg
Poids
0,65 kg
Max. Draagkracht
70kg
Paneeldikte
0-46mm
Poids
0,325 kg
Dimensions
16 × 20 × 2,2 cm
Dimensions de la surface de travail
150x150mm
Force de fixation
800gr/cm² à 6 bar
Pression de travail
5,5-7 bar
Consommation d'air à 5,5 bars
28l/min
Poids
0,05 kg
Diamètre
22mm
Longeur de coupe
19mm
Longueur
51mm
Faces de coupe
2+1
Poids
15 kg
Poids
0,05 kg
Diamètre
9,5mm
Longeur de coupe
13mm
Longueur
54mm
Faces de coupe
2
Filetage
M33
Ouverture maximale
889 mm
Poids
0,05 kg
Diamètre
4mm
Longeur de coupe
11mm
Longueur
51mm
Faces de coupe
2+1
Abonnez-vous pour notre bulletin d'information
Select the fields to be shown. Others will be hidden. Drag and drop to rearrange the order.
Image
SKU
Rating
Price
Stock
Availability
Add to cart
Description
Content
Weight
Dimensions
Additional information
Click outside to hide the comparison bar
Comparer
Nous utilisons des cookies pour nous assurer que notre site Web fonctionne aussi bien que possible. Si vous continuez à utiliser ce site Web, nous supposons que cela vous convient.OkPrivacy policy