Soldes
Idéal pour réaffûter les outils courbes, les gouges, les outils de coupe et de tournage du bois. Surface diamantée convexe et concave dans un seul outil de meulage. Réaffûtage des outils avec un rayon de min. 1,6 à max. 25 mm. Comprend un support antidérapant pour une utilisation plus facile. Pas besoin d'huile - à moudre à sec ou avec de l'eau.
Wood lubricant for machine surfaces and machine tables. Significantly improves the sliding of wood over machines in steel, cast iron or aluminium. Ideal for planers, routers, saw tables, etc. Also a great efficiency for sliding wood on wood (wooden guides, extension tables, drawers, etc.). Silicone-free. Can be used on all types of wood without leaving marks!
Advantages: does not damage glued joints, increases safety while working, increases quality of finish, leaves no traces.
Can also be used to restore shine to plastic.
SHOWROOM MODEL
The TT305SLU has the same features as the pull-function mitre saw TT305SLX, but is additionally equipped with an extra-large top table that can be adjusted from 0 to 50 mm with a convenient control knob. It is equipped with a silent 1600 W induction motor that requires no maintenance and has a pull function of up to 350 mm, with a cutting height of up to 107 mm.
The Kreg KMS7102 precision miter guide is adjustable from -45° to 45°. It is equipped with preset angles at 0°, 10°, 22.5°, 30° and 45°. The brass pin makes it easy to switch between these angles. In addition to these preset angles, the mitre stop is adjustable with 0.1° precision. Markings are indicated per 1°. The supplied guide has a length of 610 mm and has a reversible stop.
The mitre stop has an aluminium guide rail measuring 9.5 x 19 x 610 mm and has five adjustment points that you can adjust to eliminate "play" in the mitre groove with a simple turn of the screwdriver.
Most bandsaw blades do not run perfectly perpendicular to the front of the table. There is always just a little bit of "drift" that prevents you from getting precise cuts, even if you use a fence.
The Kreg® Precision Band Saw fence easily adjusts to the blade drift angle to give you a new level of band saw accuracy.
This fence can be mounted on most 356 mm (14") band saws straight out of the box and can be adapted to many others by drilling a single hole in the aluminium mounting rail.
Never before has it been possible to make such a wide variety of cuts with a band saw fence. This stop adjusts both for blade deviation and perpendicularity to the blade (essential when cutting thin veneer).
In addition, the stop can be quickly placed in an inconspicuous position, allowing the blade guides to be positioned closer to the workpiece. In addition, the fence can accept repeating sawn guides or Kreg® Stops for use in additional applications.
Puissante ponceuse à bande pour le nivellement et le travail grossier. La ponceuse LB31EA est très stable et convient à une utilisation à deux mains. Grâce à la grande surface de ponçage, cette machine atteint un rendement élevé. La grande stabilité garantit à son tour une belle finition sans rayures pour votre pièce. Il est équipé d'un extracteur de poussière intégré et d'un sac à poussière pour permettre à l'utilisateur de travailler confortablement et proprement.
Grâce à sa plus grande surface de ponçage (175x100mm), Virutex se distingue de toutes les autres ponceuses à bande sur le marché. La plus grande surface augmente la stabilité et la machine reste toujours parfaitement équilibrée et à plat sur votre pièce.
Egalement disponible avec connexion pour l'extraction de la poussière comme modèle LB31E.
Of u nu een nieuw handvat of tientallen ladeknoppen gaat monteren, met de boormal voor kastbeslag hoeft u niet langer te gissen en werkt u keer op keer nauwkeurig en consistent. Dankzij de verstelbare randgeleider en de ingebouwde meetlatten (met Engelse en metrische markeringen) is het makkelijk om knoppen heel precies te plaatsen. Bovendien heeft de boormal voor kastbeslag verplaatsbare en vastklikbare boorgeleiders van gehard staal die overeenkomen met de meest voorkomende afstanden tussen de gaten voor kastknoppen en handvatten. Met de geleiders is het kinderspel om rechte, nauwkeurig geplaatste gaten te boren. De boormal is geschikt voor zowat elk type knop of handvat, waardoor hij bijzonder veelzijdig is.
SHOWROOM MODEL
Staande houtkliefmachine voor tweehandige bediening. Deze krachtige houtkliever is perfect geschikt voor semiprofessioneel of thuisgebruik. Met behulp van deze kliefmachine klieft u probleemloos houtstukken tot 1000mm lengte (mits verlengstuk 3GRLAKR) en diameter 450mm. De tafel kan ingesteld worden op drie hoogtes 520mm - 900mm of 1300mm. Qua prestaties is dit model identiek aan de TT1350/12T met als verschil dat dit model is voorzien van een benzinemotor van 6.5 PK(Briggs & Stratton). Tot 11 ton drukkracht. Dankzij het compacte design is deze klover gemakkelijk op te bergen of te verplaatsen. Eenvoudig verrijdbaar dankzij de rubberen banden.
SHOWROOM MODEL - UNUSED
The TT255UTC offers all the possibilities of a mitre saw and, thanks to its top table with guide, it is also ideally suited for cutting boards lengthwise. Its compactness and low weight make it particularly convenient to take with you when working on the move.
Lichte en krachtige mini vlakschuurmachine voor het polijsten en afwerken van uw werkstukken. Deze machine onderscheidt zich van het model LR84H door zijn dubbele beweging. De schuurzool beweegt zowel roterend als excentrisch. Standaardlevering met Delta opzetstuk en ronde schuurplaat (Ø125mm). Voorzien van een geïntegreerde stofafzuiging en stofzak. Met elektronische snelheidsregeling en remsysteem voor de schuurzool.
Optioneel verkrijgbaar in een handige PVC koffer.
Modèle de salle d'expo
Scie à ruban portative et pratique, de construction entièrement en aluminium, pour les travaux généraux de menuiserie ou de profilage. Equipée d’un puissant moteur à induction 230 V. Grâce à son boîtier en aluminium, cette machine est, malgré ses dimensions, relativement légère. La grande plaque de guidage, le poids bien équilibré et la large poignée rendent cet appareil exceptionnellement facile à utiliser. Les fentes dans la plaque de guidage garantissent que la ligne de coupe reste toujours bien visible. La double capacité de sciage élimine la nécessité d'incliner la lame de scie. En d'autres termes, cette machine vous offre des possibilités d'usinage infinies à un prix bas.
Modèle de salle d'expo
Cette machine combinée compacte de la série Hobby+ est un sommet absolu dans sa catégorie de prix. La machine idéale pour tout menuisier qui travaille à la maison ou dans un petit atelier. Composé de deux machines différentes, ce Combi Workcentre vous offre trois fonctions : le sciage, le fraisage et le rabotage - dégauchissage Chaque fonction est commandée par un moteur à induction distinct de 230V. Cette machine combinée peut également être divisée en deux parties. Ainsi, vous pouvez utiliser séparément la table de scie + la fraiseuse et la rabot-dégau.
Le kit de roues WK600 est disponible en option. Attention! Le kit de roues ne peut être utilisé qu'avec les extensions.
Deze betonschuurder werd speciaal ontworpen voor het wegslijpen van betonnen delen, opschuren van oude betonlagen of het verwijderen van overgangen tussen bekisting en betonlopers. Optimale voorbereiding voor verdere coatings. De betonschuurder heeft een metalen behuizing en afzuiging. Deze afzuiging voorkomt stofhinder, wat op zijn beurt zorgt voor minder slijtage van de schijf en de poriën van het beton open blijven. Voorzien van een diamantkop korrel 24, een betrouwbare 1200W-motor. Tevens werd een blokkeersysteem voorzien, zodoende kunnen de diamantkoppen veilig gewisseld worden. vibratie gedempte, ergonomische beugelhangreep (90° draaibaar) voor optimale bediening en controle over het toestel. Een luchtstroomkoeling mindert de lawaaihinder tot het absolute minimum. Max toerental 9.500.
Content
Idéal pour réaffûter les outils courbes, les gouges, les outils de coupe et de tournage du bois. Surface diamantée convexe et concave dans un seul outil de meulage. Réaffûtage des outils avec un rayon de min. 1,6 à max. 25 mm. Comprend un support antidérapant pour une utilisation plus facile. Pas besoin d'huile - à moudre à sec ou avec de l'eau.
Wood lubricant for machine surfaces and machine tables. Significantly improves the sliding of wood over machines in steel, cast iron or aluminium. Ideal for planers, routers, saw tables, etc. Also a great efficiency for sliding wood on wood (wooden guides, extension tables, drawers, etc.). Silicone-free. Can be used on all types of wood without leaving marks!
Advantages: does not damage glued joints, increases safety while working, increases quality of finish, leaves no traces.
Can also be used to restore shine to plastic.
The TT305SLU has the same features as the pull-function mitre saw TT305SLX, but is additionally equipped with an extra-large top table that can be adjusted from 0 to 50 mm with a convenient control knob.
It is equipped with a silent 1600 W induction motor that requires no maintenance (which is a big advantage over the carbon brush motor in the smaller models) and has a pull function of up to 350 mm, with a cutting height of up to 107 mm.
The use of ball bearings on all joints ensures precise rotation of the table, head and tilting system. The saw has a die-cast aluminum body and can be tilted up to 48° in 2 directions. The silent, maintenance-free 1600 W induction motor delivers high torque and is positioned at the rear, giving the saw a large cutting height (up to 107 mm). The saw blade has a diameter of 305 mm and 60 teeth. The side supports are extendable.
The TT305SLU is further equipped with a horizontal D handle.
The Kreg KMS7102 precision miter gauge is adjustable from -45° to 45°. It is equipped with preset angles at 0°, 10°, 22.5°, 30° and 45°. The brass pin makes it easy to switch between these angles. In addition to these preset angles, the mitre stop is adjustable with 0.1° precision. Markings are indicated per 1°. The supplied guide has a length of 610 mm and has a reversible stop.
The mitre stop has an aluminium guide rail measuring 9.5 x 19 x 610 mm and has five adjustment points that you can adjust to eliminate "play" in the mitre groove with a simple turn of the screwdriver.
Most bandsaw blades do not run perfectly perpendicular to the front of the table. There is always just a little bit of "drift" that prevents you from getting precise cuts, even if you use a fence.
The Kreg® Precision Band Saw fence easily adjusts to the blade drift angle to give you a new level of band saw accuracy.
This fence can be mounted on most 356 mm (14") band saws straight out of the box and can be adapted to many others by drilling a single hole in the aluminium mounting rail.
Never before has it been possible to make such a wide variety of cuts with a band saw fence. This stop adjusts both for blade deviation and perpendicularity to the blade (essential when cutting thin veneer).
In addition, the stop can be quickly placed in an inconspicuous position, allowing the blade guides to be positioned closer to the workpiece. In addition, the fence can accept repeating sawn guides or Kreg® Stops for use in additional applications.
Straight, strong and rigid design
The aluminium fence is incredibly strong, straight and built to last for years. The front and top of the fence contain T-slots for adding stops, guides for repeating saws and more.
Easy to remove
When you don't need the fence, remove it in seconds - no tools needed! Simply loosen the locking button and lift the fence off the mounting rail, which is below the table surface, so that it is not in the way.
Precision Lens Cursors
The thin red line on the Precision Lens Cursor is enlarged and easy to read for even the smallest adjustments, allowing you to fine-tune the stop for cutting veneers, pins and more.
Adjustable in two sizes
This fence is unique in that it can adjust itself to fit perfectly square to your table and top. With two simple adjustments, you can set the stop to match the blade deviation, thus significantly improving cutting accuracy.
Usability
Pre-drilled holes on the mounting rail are suitable for most 356 mm (14") band saws.
Puissante ponceuse à bande pour le nivellement et le travail grossier. La ponceuse LB31EA est très stable et convient à une utilisation à deux mains. Grâce à la grande surface de ponçage, cette machine atteint un rendement élevé. La grande stabilité garantit à son tour une belle finition sans rayures pour votre pièce. La machine est équipée de bouchons en carbure de haute qualité (widia) pour éviter l'usure du boîtier. Il est équipé d'un extracteur de poussière intégré et d'un sac à poussière pour permettre à l'utilisateur de travailler confortablement et proprement. Plusieurs bandes abrasives de différentes granures sont disponibles en option.
Grâce à sa plus grande surface de ponçage (175x100mm), Virutex se distingue de toutes les autres ponceuses à bande sur le marché. La plus grande surface augmente la stabilité et la machine reste toujours parfaitement équilibrée et à plat sur votre pièce.
Egalement disponible avec connexion pour l'extraction de la poussière comme modèle LB31E.
Of u nu een nieuw handvat of tientallen ladeknoppen gaat monteren, met de boormal voor kastbeslag hoeft u niet langer te gissen en werkt u keer op keer nauwkeurig en consistent. Dankzij de verstelbare randgeleider en de ingebouwde meetlatten (met Engelse en metrische markeringen) is het makkelijk om knoppen heel precies te plaatsen. Bovendien heeft de boormal voor kastbeslag verplaatsbare en vastklikbare boorgeleiders van gehard staal die overeenkomen met de meest voorkomende afstanden tussen de gaten voor kastknoppen en handvatten. Met de geleiders is het kinderspel om rechte, nauwkeurig geplaatste gaten te boren. De boormal is geschikt voor zowat elk type knop of handvat, waardoor hij bijzonder veelzijdig is.
Staande houtkliefmachine voor tweehandige bediening. Deze krachtige houtkliever is perfect geschikt voor semiprofessioneel of thuisgebruik. Met behulp van deze kliefmachine klieft u probleemloos houtstukken tot 1000mm lengte (mits verlengstuk 3GRLAKR) en diameter 450mm. De tafel kan ingesteld worden op drie hoogtes 520mm - 900mm of 1300mm. Qua prestaties is dit model identiek aan de TT1350/12T met als verschil dat dit model is voorzien van een benzinemotor van 6.5 PK(Briggs & Stratton). Met behulp van deze motor levert deze houtklover een kracht tot 11 ton! Daardoor is de klover geschikt om meerdere houtsoorten te splijten. Dankzij het compacte design is deze klover gemakkelijk op te bergen of te verplaatsen. Eenvoudig verrijdbaar dankzij de rubberen banden.
The TT255UTC offers all the possibilities of a mitre saw and, thanks to its top table with guide, it is also ideally suited for cutting boards lengthwise. Its compactness and low weight make it particularly convenient to take with you when working on the move.
The use of ball bearings on all joints ensures precise rotation of the table, head and tilting system. The compact and lightweight saw has a die-cast aluminum body, a very compact 255 mm saw blade with 48 teeth, a large, easily adjustable top table with robust guide and a clear mitre indicator. The motor has belt drive, which provides great torque, and is positioned at the rear, giving the saw a large cutting height.
The TT255UTC is further equipped with an ergonomic vertical D handle, which ensures that the up and down movement is performed from the wrist rather than the shoulder. An added benefit of this handle is that it can be used with either the left or right hand.
Lichte en krachtige mini vlakschuurmachine voor het polijsten en afwerken van uw werkstukken. Deze machine onderscheidt zich van het model LR84H door zijn dubbele beweging. De schuurzool beweegt zowel roterend als excentrisch. Het ergonomische ontwerp zorgt voor een perfecte houvast en comfortabel werken. Al de bedieningselementen zijn eenvoudig bereikbaar tijdens het werken. Standaardlevering met Delta opzetstuk om moeilijk te bereikbare plaatsen zoals hoeken of jaloezieën toch te kunnen schuren. Het Delta stuk is zowel boven- als onderaan voorzien van klittenband / velcro om schuurpapier te bevestigen. Nog standaard geleverd met een ronde schuurplaat (Ø125mm). Voorzien van een geïntegreerde stofafzuiging en stofzak. Met elektronische snelheidsregeling en remsysteem voor de schuurzool.
Optioneel verkrijgbaar in een handige PVC koffer.
Scie à ruban portative et pratique, de construction entièrement en aluminium, pour les travaux généraux de menuiserie ou de profilage. Equipée d’un puissant moteur à induction 230 V. Grâce à son boîtier en aluminium, cette machine est, malgré ses dimensions, relativement légère. La grande plaque de guidage, le poids bien équilibré et la large poignée rendent cet appareil exceptionnellement facile à utiliser. Les fentes dans la plaque de guidage garantissent que la ligne de coupe reste toujours bien visible. La double capacité de sciage élimine la nécessité d'incliner la lame de scie. En d'autres termes, cette machine vous offre des possibilités d'usinage infinies à un prix bas. La machine est équipée de série d'une lame de scie d'une longueur de 1710 mm et d'une largeur de 6 mm. La lame de scie est également disponible en largeur 10, 13, 16 et 20 mm en option.
Cette machine combinée compacte de la série Hobby+ est un sommet absolu dans sa catégorie de prix. La machine idéale pour tout menuisier qui travaille à la maison ou dans un petit atelier. Composé de deux machines différentes, ce Combi Workcentre vous offre trois fonctions : le sciage, le fraisage et le rabotage - dégauchissage Chaque fonction est commandée par un moteur à induction distinct de 230V. La table de sciage est équipée d'un chariot avec un guide télescopique à butée basculante, un réglage fin et un dispositif de serrage rapide. La lame de scie peut être inclinée jusqu'à 45° pour une coupe en biais. Vous pouvez également utiliser ce chariot comme chariot à tenonner pour la toupie.
Table de fraisage
La toupie (avec un arbre de Ø30mm) est réglable à trois vitesses. La vitesse la plus basse est principalement recommandée pour les travaux de fraisage lourds, tels que faire des tenons. A des vitesses plus élevées, ce type de travail peut avoir un "effet d'hélicoptère", où le cutter décolle. Les vitesses plus élevées se prêtent parfaitement au profilage. Réglez donc toujours la bonne vitesse en fonction du type de matériel et du type de travail que vous effectuez. La table de routage est équipée d'un couvercle de routeur pour que vous puissiez toujours travailler en toute sécurité.
Raboteuse-dégauchisseuse
En outre, cette machine combinée vous offre également une puissante machine à raboter et dégauchisser. La conception robuste en acier avec des surfaces de travail en fonte rend cette machine résistante à un usage quotidien intensif. Les tables de dégauchissage sont équipées d'un profil lourd en bas pour maintenir la planéité à tout moment. Les tables sont articulées indépendamment et peuvent être relevées. De cette façon, vous pouvez utiliser au maximum les capacités de la raboteuse.
Afin de pouvoir dégauchir très précisément, cette machine est équipée d'un solide guide en aluminium sur le dessus. Ce guide peut être réglé à un angle avec deux butées pour 90° et 45°. Grâce à l'arbre de rabotage lourd, équipé de trois fers de rabotage, une bonne finition est toujours garantie. Les copeaux sont évacués par une capot à charnière. Cette capot peut être raccordée à un système d'extraction des poussières grâce à la sortie Ø100mm.
Cette machine combinée peut être divisée en deux parties. Ainsi, vous pouvez utiliser séparément la table de scie + la fraiseuse et la rabot-dégau.
Deze betonschuurder werd speciaal ontworpen voor het wegslijpen van betonnen delen, opschuren van oude betonlagen of het verwijderen van overgangen tussen bekisting en betonlopers. Optimale voorbereiding voor verdere coatings. De betonschuurder heeft een metalen behuizing en afzuiging. Deze afzuiging voorkomt stofhinder, wat op zijn beurt zorgt voor minder slijtage van de schijf en de poriën van het beton open blijven. Voorzien van een diamantkop korrel 24, een betrouwbare 1200W-motor. Tevens werd een blokkeersysteem voorzien, zodoende kunnen de diamantkoppen veilig gewisseld worden. vibratie gedempte, ergonomische beugelhangreep (90° draaibaar) voor optimale bediening en controle over het toestel. Een luchtstroomkoeling mindert de lawaaihinder tot het absolute minimum. Max toerental 9.500.
Weight
2 kg
1 kg
34 kg
3,5 kg
4 kg
6,5 kg
1 kg
180 kg
18 kg
1,5 kg
19 kg
250 kg
2,9 kg
Dimensions
ND
ND
580 × 890 × 540 cm
ND
ND
ND
ND
ND
620 × 490 × 420 cm
ND
ND
ND
ND
Additional information
Poids
2 kg
Poids
1 kg
Poids
34 kg
Dimensions
580 × 890 × 540 cm
Epaisseur de coupe maximale
107 mm
Puissance
1600 W
Coupe 0° x 0°
350 x 107 mm
Coupe 0° x 45°
240 x 94 mm
Coupe 45° x 0°
350 x 70 mm
Coupe 45° x 45°
240 x 70 mm, 55 x 55 mm
Diamètre lame de scie
305mm
Poids
3,5 kg
Poids
4 kg
Longueur
457 mm, 660 mm
Poids
6,5 kg
Puissance
1200W
Dimensions de la bande
690x100mm
Surface de ponçage
175x100mm
Vitesse de la bande
420m/min
Poids
1 kg
Materiaal boorsjabloon
kunststof
Materiaal boorgeleiders
gehard staal
Onderlinge afstand gaten
64 mm, 76 mm, 89 mm, 96 mm, 101 mm, 114 mm, 127 mm
Afstand gaten tot rand
25 tot 127 mm
Poids
180 kg
Moteur
6 PK
Max. lengte hout
1000mm
Max. Ø hout
450mm
Poids
18 kg
Dimensions
620 × 490 × 420 cm
Epaisseur de coupe maximale
40 mm
Voltage
230 V
Puissance
1600 W
Coupe 0° x 0°
150 x 70 mm
Coupe 0° x 45°
100 x 70 mm
Coupe 45° x 0°
150 x 45 mm
Coupe 45° x 45°
55 x 45 mm
Diamètre lame de scie
255 mm
Poids
1,5 kg
Puissance
180W
Schuuroppervlakte
80x130mm
Ø Rotatie
2mm
Nominale snelheid
7000-12500rpm
Vibrations
14000-25000/min
Poids
19 kg
Moteur
1 PK
Hauteur de coupe
300mm
Longueur du ruban de scie
1710mm
Min. - Largeur max. du ruban de scie
6-20mm
Vitesse à vide
1410rpm
Plaque de guidage
420x310mm
Vitesse de coupe
900m/min
Poids
250 kg
Moteur
1.5 CV, 2 PK
Voltage
230 V
Table de travail (sciage / fraisage)
940x410mm
Chariot table
400x250mm
Chariot longeur
1000mm
Hauteur de rainure
76,5mm
Trou de fraisage
140mm
Diamètre de l\' arbre
30 mm
Vitesse à vide (fraisage)
4500rpm, 6500rpm, 8500rpm
Profondeur de coupe 45°
40mm
Profondeur de coupe 90 °
60mm
Vitesse à vide (sciage)
4750rpm
Table de travail (rabotage-dégauchissage)
1085×256
Schaafbreedte
250mm
Profondeur de rabotage-dégauchissage
3mm
Table de travail (dégauchissage)
600x258mm
Profondeur de dégauchissage
2mm
Hauteur de la raboteuse
5-180mm
Vitesse d'alimentation de la raboteuse
5m/min
Vitesse à vide (arbre de rabotage)
4000rpm
Poids
2,9 kg
Puissance
1200W
Toerental
9500 tr/minuut
Abonnez-vous pour notre bulletin d'information
Select the fields to be shown. Others will be hidden. Drag and drop to rearrange the order.
Image
SKU
Rating
Price
Stock
Availability
Add to cart
Description
Content
Weight
Dimensions
Additional information
Click outside to hide the comparison bar
Comparer
Nous utilisons des cookies pour nous assurer que notre site Web fonctionne aussi bien que possible. Si vous continuez à utiliser ce site Web, nous supposons que cela vous convient.OkPrivacy policy