Met behulp van deze balfrees maakt u snel en eenvoudig groeven voor schuifpanelen of elektrische bedrading. Dankzij de snijvlakken in hoogwaardig hardmetaal (widia) gebruikt u deze frees probleemloos op de meeste houtsoorten. Gebruik een rechte frees om een voorgroef te maken zodat de schacht van de balfrees zich vrij kan bewegen.
Deze set bestaat uit twee freeskoppen in lichtmetaal, uitgerust met hardmetalen messen (HW). Maak stevige verbindingen met behulp van de profiel- contraprofielfrees, of frees bossingen met de platbandfrees. Samen bieden deze twee freeskoppen u alles wat u nodig heeft om hoogwaardige, en mooi afgewerkte keukenkastdeuren te maken.
Standaard staat op de profiel- contraprofiel frees het profielmes type A gemonteerd. Op aanvraag zijn ook type B, C en D verkrijgbaar. Deze frees heeft een diameter van 120mm, voor meer informatie en alle technische gegevens zie art. ST-YH102AAM.
De bossingfrees bestaat uit twee messen die los van elkaar te verstellen zijn. Door de messen in verhouding van elkaar anders uit te lijnen, krijgt u de mogelijkheid om verschillende profielen te creëren, bijvoorbeeld met of zonder opstaande rand. Deze frees heeft een diameter van 183mm. De freeshoogte en snijlengte zijn afhankelijk van de manier waarop u de messen heeft ingesteld. Zie de extra informatie onderaan voor meer technische gegevens over deze frees.
Forstner drill bit with cylindrical shank for boring hinges with the best quality on every kind of wood or panels. This high quality hinge boring bit has two Tungsten cutting edges, two Tungsten spurs and a HW center point for boring with the best quality on every kind of wood or panels. Right hand boring only
Set profielmessen hoogte 40mm Nr. 0010 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Set profielmessen hoogte 40mm Nr. 0029 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Saw blade with 24 teeth
Multipurpose saw blade with WZ alternate top bevel teeth for quickly cutting along and across grain of all natural woods, wooden boarding materials or one sided veneer and plastic coated materials. For use on table saws. No noise saw blades.
Groefzaagblad met vlakke (FZ), widia zaagtanden om groeven te trekken in hardhout, zacht hout, gelamineerde panelen en andere producten op basis van hout. De zaagbladen hebben een asgat van 30mm en zijn ideaal voor gebruik op freesmachines of op zaagtafels.
Dit zaagblad is beschikbaar in verschillende diameters
Deze pneumatische vacuümtafel is ontworpen om gladde, niet poreuze werkstukken vast te klemmen. Het vacuüm tussen de basis van de tafel en het werkstuk zorgt voor een stevige klemming en laat na gebruik geen sporen na. Om de tafel vacuüm te maken dient ze aangesloten te zijn op een externe compressor (niet inbegrepen). Dankzij het compacte formaat is deze vacuümtafel zowel geschikt om in het atelier te gebruiken als daarbuiten. Omdat u de tafel zowel verticaal als horizontaal kan plaatsen is deze module ideaal voor een brede waaier aan toepassingen.
Met behulp van de standaard inbegrepen rubber dichtingen verdeelt u de tafel eenvoudig in kleinere secties. Standaardlevering met één rubber dichting al geïnstalleerd en een transparante tube voor de luchttoevoer met 1/4" snelkoppeling.
Deze verstelbare afschuinfrees met snijvlakken in hoogwaardig hardmetaal, geeft u een enorme flexibiliteit bij het maken van schuine kanten. De frees is aan beide zijden instelbaar tussen 0° en 90° met stappen van 7,5°. Gebruik de frees zowel voor het afschuinen van hout als plaatmateriaal. Dankzij de hardmetalen messen snijdt deze groeffrees moeiteloos door massieve platen, harde en zachte houtsoorten, MDF of gelamineerde platen.
You can attach this accessory to the GuidePRO so that you can secure the GuidePRO in your miter slot. Ideal for repetitive and consistent cuts. The GuidePRO comes with a miter cam connector and is designed for quick set-ups and offers excellent feeding benefits for band saw cuts. Some GuidePRO users want the benefits of the GuidePRO, but as a fixed-position tool. The GuidePRO anchor bar locks the GuidePRO securely in place, so you don't have to move the tool with every cut.
GuidePRO Anchor Bar extends the use of the GuidePRO to the router table and table saw.
Levage facile et sûr des panneaux de porte, meubles, ... Cet ascenseur de porte a une capacité de charge allant jusqu'à 200 kg. Équipé d'une base pivotante et d'une surface antidérapante. Fabriqué en aluminium. Hauteur maximale de levage 75cm.
Les presseurs Belmash offrent une sécurité accrue lorsque vous travaillez avec votre raboteuse. Planifiez en toute sécurité des poutres ou des planches sur n'importe quelle machine Belmash. La pince assure que la pièce est serrée sur la surface de travail. Cela facilite la circulation des matériaux, vous donnant une finition propre et précise. Ces dispositifs de serrage sont faciles à installer à l'aide des vis et des rondelles. L'ouverture peut être réglée à l'aide d'une poignée sur le dessus et d'une pince à ressort sur le côté. De cette manière, une bonne alimentation et une bonne force de pression sont toujours assurées.
Cette presseur peut être utilisé sur le Belmash SDMR2500.
Fraise à rainurer à lames réversibles et précouteaux en carbure de haute qualité (HW) pour réaliser des rainures de précision. Réglable progressivement en hauteur entre 28mm et 55mm. Grâce aux lames en carbure de tungstène, cette fraise à rainurer coupe sans effort les planches massives, les bois durs et tendres, le MDF ou les planches laminées.
Disponible avec un alésage de 30 mm ou 50 mm.
Avec les guides de stock de précision, vous n'avez plus à vous battre pour tenir des plaques ou des poutres tout en poussant sur la scie - et la table de fraisage. Les rouleaux tirent votre pièce en la plaçant fermement contre le guide et votre table de travail. Vous couperez de manière plus sûre, plus facile et plus précise tout en maintenant votre pièce en place à tout moment.
Set profielmessen hoogte 40mm Nr. 0061 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Forstner drill bit with cylindrical shank for boring hinges with the best quality on every kind of wood or panels. This high quality hinge boring bit has two Tungsten cutting edges, two Tungsten spurs and a HW center point for boring with the best quality on every kind of wood or panels. Right hand boring only
L'unité de rabotage est un outil indispensable pour le rabotage d'épaisseur sur le Belmash SDM2500 et permet d'obtenir une pièce d'excellente qualité. Il possède son propre bloc de coupe qui est entraîné par le moteur du SDM2500. Avec cet appareil, vous pouvez prévoir une épaisseur sur le SDM2500 de 5 à 103 mm et une largeur de rabotage de 250 mm.
Forstner drill bit with cylindrical shank for boring hinges with the best quality on every kind of wood or panels. This high quality hinge boring bit has two Tungsten cutting edges, two Tungsten spurs and a HW center point for boring with the best quality on every kind of wood or panels. Right hand boring only
READYtoWORK pakket van paneelzaag ITAMAC Maestro X7 CNC 3200mm inclusief afzuiginstallatie, afzuigslang, klembanden, montageklemmen etc. en set van hoofdzaagblad en voorritser voor afwerking plaatmateriaal. Formaatzagen met brede geanodiseerde aluminium roltafel op dubbele slijtvaste staafgeleiding met vervangbare rollers. Voorzien van een ingebouwde module start/stop systeem welke garant staat voor een optimaal gebruikscomfort.
Ces supports en acier à ressort galvanisé se montent au mur en quelques secondes et sont parfaits pour ranger des outils ou des accessoires d'un diamètre de 10 cm, tels que les nouveaux accessoires Air Flux. Les pièces de montage, le tuyau d'extraction flexible et d'autres outils avec un Ø 100 mm s'adaptent parfaitement ici.
Le Kreg Pocket-Hole Jig 720 Pro est le système de connexion professionnel, rapide et efficace avec des accessoires haut de gamme. Avec ce système, vous pouvez réaliser des trous de poche très résistants dans des matériaux d'une épaisseur minimale de 13 mm (1/2") et d'une épaisseur maximale de 38 mm (1 1/2").
Le Kreg 720 Pro est livré avec une station d'accueil. Cette extension offre plus de support pour des équipements plus volumineux et plus d'espace de stockage. Les pièces latérales de la station d'accueil peuvent être facilement pliées pour ranger le système lorsqu'il n'est pas utilisé. De plus, les pièces latérales peuvent également être déconnectées du système afin que vous puissiez créer encore plus de support pour votre pièce.
Vous pouvez mesurer l'épaisseur du matériau à l'aide de la jauge d'épaisseur fournie. Au bas du gabarit Kreg Pocket-Hole Jig 720 se trouve un système de rangement intégré pour la perceuse, les embouts et la jauge d'épaisseur du matériau.
Set profielmessen hoogte 50mm Nr. 2010 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
The updated DUROTEC structure brush machine is more powerful and compact and can run even slower for a better finish. The double reduction gearing allows you to apply pressure without the machine slowing down for extra correction force. The ergonomic design and lightweight make this machine perfect for handling during brushing, satin finishing, or structuring your workpiece. Durotec is an extremely compact machine with an ergonomic handy D handle.
Double reduction gearing
Adjustable speed 1200-3900 rpm
Marathon motor 800 W, constant torque
Ergonomic handle
Comes standard with DUROGRIND K80 fleece brush. Numerous brushes available optionally for both wood and metalworking.
Fonctionne avec toutes les machines jusqu'à 7,5 KW. Connecter plusieurs machines afin qu'elles puissent être mises en marche ensemble. Utilisez ce démarreur simultané lorsque vous combinez une machine à bois et un système de dépoussiérage. Le moteur de démarrage assure le démarrage automatique de votre aspirateur quatre secondes après que vous ayez vous-même mis en marche votre machine à bois. Après avoir arrêté votre machine à bois, l'extraction est également arrêtée quelques secondes plus tard. Ces quelques secondes supplémentaires d'aspiration garantissent que vos tuyaux sont toujours propres.
Bandsaw blade with length 3607mm for use on the TT500X band saw machine from Tendotools. This saw blade has 3 TPI (teeth per inch) and has a width of 25mm. This bandsaw blade in tempered steel "Flexback" is very suitable for multipurpose sawing. Use this saw ribbon for both wood and plastics. The teeth of the saw blade were given an additional heat treatment for increased hardness. This keeps the band very supple and increases your cutting comfort thanks to the hardness of the teeth.
Extra afvalzakken in PVC 120µm voor gebruik met de stofafzuigingen van Air Flux. Deze zakken kunnen gebruikt worden met de Air Flux Dusty 1020AF.
Les dents de cette lame de scie sont aiguisé en forme de V (45°) pour facilement et rapidement faire des rainures dans votre lambris. Sur demande, les dents peut être aussi aiguiser en différents formes/angles ou avec des épaisseurs différents.
Lame de scie pour rainues avec denture widia en forme V pour faire des rainures dans des bois durs, tendres, exotiques et des panneaux avec revêtement en plastique. Les lames de scie ont un alésage de 30mm et sont idéal à utiliser sur des toupies ou des scies à table.
Tenoning jig TJ-85 for the Itamac Panthera (Harvest) HW110SE table saws.
Ideal for sawing tenons etc.
Straight router bits are specifically designed for making grooves in most types of wood or several plastics. Together with two straight cutting edges, there is a special tip on the bottom (Z=2+1) which allows easy and precise boring. This router bit can be used to work on most wood types or plastics. Thanks to the high quality finish of the bit, it is also possible to make grooves on different plastics such as acrylics (plexiglass), polycarbonate, polypropylene or PVC. To be used in router milling machines or CNC machines.
Forstner drill bit with cylindrical shank for boring hinges in most wood types or panels. This high quality hinge boring bit has two Tungsten cutting edges, two Tungsten spurs and a HW center point for boring with the best quality on every kind of wood or panels. Right hand boring only
This boring bit is available in two lengths
Convenient all in one set to make dovetail joints with the Virutex PL11. The set includes an interchangeable PVC mould with tooth spacing (pas) 34mm, an adapted guide ring Ø23mm and the correct dovetail bit Ø19mm. Use this set to make large dovetail joints (e.g. for furniture). Minimum thickness of the wood to be able to work correctly is 24mm.
Guide rail, used as an extension for the rail which is delivered as a standard wih the plunge-cut saws TT55 and TT85. Length 800 or 1400 mm.
Set de couteaux profilés hauteur 40mm Nr. 0064 pour des porte-outils à profiler universels. Approprié pour le fraisage de profilés de chants en bois massif avec un faible coût d'outillage. Acier à outils allié avec 16% cobalt pour un qualité de coup très haut et un fraisage confortable.
Ø 100mm Keyed hose clamps have a thumbscrew that allows you to quickly tighten or loosen without a screwdriver or wrench. Makes setting up, modifying or cleaning your dust collection system easier! For use with Ø 100 mm extraction hoses and connectors.
Set of 5 pieces.
Joint isolant en silicone pour fenêtres et portes de couleur blanche. Excellente résistance à des températures comprises entre -60 et 200°C. Avec ce sceau, vous bénéficierez à la fois d'une bonne isolation température et d'une bonne isolation acoustique. Essentiel pour les nouvelles constructions et facile à intégrer dans les constructions existantes. Utilisez la rainureuse Virutex RA17VG avec le mèche ancre double.
Disponible en diamètre 6mm ou 8mm.
Koppelstuk 45° met diameter 100mm om te gebruiken in combinatie met de Air Flux stofafzuigingssystemen.
Set de couteaux profilés hauteur 40mm Nr. 0026 pour des porte-outils à profiler universels. Approprié pour le fraisage de profilés de chants en bois massif avec un faible coût d'outillage. Acier à outils allié avec 16% cobalt pour un qualité de coup très haut et un fraisage confortable.
Straight router bits are specifically designed for making grooves in most types of wood or several plastics. These router bits are finished with carbide cutting edges. Thanks to the carbide cutting edges, the router bit delivers high quality results for all your projects and a long working life.
This router bit can be used to work on most wood types or plastics. Thanks to the high quality finish of the bit, it is also possible to make grooves on different plastics such as acrylics (plexiglass), polycarbonate, polypropylene or PVC. To be used in router milling machines or CNC machines.
The TT255SL is a mitre saw with pull function and the little sister of the TT305SLX. It is equipped with a noiseless 1600 W induction motor that requires no maintenance (which is a big advantage over the carbon brush motor in the smaller models) and has a pull function up to 300 mm, with a cutting height up to 60 mm.
Klein® trimming bits with straight cut are suitable for smooth and well-finished edges on melamine and veneered panels. The ball bearing, having the same diameter of the cutters, trims any overlap leaving a flat and smooth edge. Two flutes provide fast cutting and good chipping ejection.
Fraises à rainurer sont spécifiquement conçue pour faire des rainures dans des types de bois différents ou des plastiques. Ces fraises sont fournis de faces de coupe en carbide. Grâce à ces faces de coupe en carbide le fraise vous assure un résultat parfait de tous votre projets ét une longue durée de vie.
Ce fraise peut être utiliser avec le plupart de types de bois. Grâce a la qualité extraordinaire il est aussi possible d'utiliser les fraises sur les plastiques comme l'acrylat (Plexiglas), polycarbonate, polypropylène ou de PVC. A utiliser dans des défonceuses ou des machines CNC.
Set profielmessen hoogte 40mm Nr. 0080 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Foret forstner avec queue cylindrique pour percer des charnières invisibles dans le plupart des bois ou panneaux. Cette mèche charnière de haute qualité avec pointe de centrage, deux faces de découpage en widia et deux guides en widia vous assure une finition parfait de tous vos trous. Rotation à droite uniquement.
Lamelles par boîte 1000 pièces. Fabriqué à partir de bois européens de haute qualité. Grâce à sa structure extra absorbante.
Set profielmessen hoogte 40mm Nr. 0003 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Cette table à vide électrique sur pied basculant est conçue pour serrer des pièces lisses et non poreuses. Pour que la table soit à vide, elle doit être connectée au système de fixation électrique à vide SVE600 de Virutex (inclus en standard). Grâce à sa taille compacte, cette table à vide peut être utilisée aussi bien dans l'atelier qu'à l'extérieur. La tête du support peut s'incliner de 90° afin que vous puissiez placer la pièce dans une position idéale. De plus, la plaque supérieure peut être tournée à 360°. Le support doit être fixé à l'aide de pinces (non comprises).
En utilisant les joints en caoutchouc fournis en standard, vous pouvez facilement diviser le tableau en sections plus petites. Livraison standard avec un joint en caoutchouc déjà installé et un tube transparent pour l'alimentation en air avec un raccord rapide de 1/4".
Top table à utiliser sur la base mobile Belmash. En utilisant la top table, la machine peut être placée séparément sur la base mobile afin que vous puissiez facilement l'emporter avec vous dans la voiture. La top table peut être utilisée en combinaison avec la base mobile PK2 et est suffisamment grande pour accueillir les modèles Universal 2000, SDM2500, SDMR2500 ou SDR2200.
Bandsaw blade with length 2240mm for use on the TT312 band saw machine from Tendotools. This saw blade has 6 TPI (teeth per inch) and has a width of 6mm. This bandsaw blade in tempered steel "Flexback" is very suitable for multipurpose sawing. Use this saw ribbon for both wood and plastics. The teeth of the saw blade were given an additional heat treatment for increased hardness. This keeps the band very supple and increases your cutting comfort thanks to the hardness of the teeth.
Forstner drill bit with cylindrical shank for boring hinges with the best quality on every kind of wood or panels. This high quality hinge boring bit has two Tungsten cutting edges, two Tungsten spurs and a HW center point for boring with the best quality on every kind of wood or panels. Right hand boring only
This extension can be placed on the left or right side of the Virutex table MT58K. Work easily with longer pieces on your table.
Guide rail or jig for circles and ovals with maximum diameter and main axis 3200mm. This compass is ideal for making mirrors, windows, doors, or any other creation with a circular or elliptical shape. To mill out an elliptical shape, use both swivel supports and elongated guides. By using just one of the two swivel supports you can mill perfect circles. Place the support exactly in the centre of the mould to make circles.
The guide rail is equipped with two powerful suction cups to attach to your panels without damage. If it is not possible to use the suction cups (e.g. on porous materials), the mould is provided with holes to screw them on. Standard delivery with two rods (Ø8mm) to attach the router to the guide.
Straight router bits are specifically designed for making grooves in most types of wood or several plastics. These router bits are finished with carbide cutting edges. Thanks to the carbide cutting edges, the router bit delivers high quality results for all your projects and a long working life.
This router bit can be used to work on most wood types or plastics. Thanks to the high quality finish of the bit, it is also possible to make grooves on different plastics such as acrylics (plexiglass), polycarbonate, polypropylene or PVC. To be used in router milling machines or CNC machines.
Straight router bits are specifically designed for making grooves in most types of wood or several plastics. Together with two straight cutting edges, there is a special tip on the bottom (Z=2+1) which allows easy and precise boring. These router bits are finished with carbide cutting edges. Thanks to the carbide cutting edges, the router bit delivers high quality results for all your projects and a long working life.
This router bit can be used to work on most wood types or plastics. Thanks to the high quality finish of the bit, it is also possible to make grooves on different plastics such as acrylics (plexiglass), polycarbonate, polypropylene or PVC. To be used in router milling machines or CNC machines.
The BOW FeatherPRO featherboard features an innovative use of high-density EVA Foam / foam combs and clamping system that increase control of insertion, dramatically improve recoil and protects your wood better from damage. This compared to the general plastic feaherboards. EVA is a high density, closed cell material with long life that you don't have with the common plastic featherboards. Ideal for table saws, routers, guides
Straight router bits are specifically designed for making grooves in most types of wood or several plastics. These router bits are finished with carbide cutting edges. Thanks to the carbide cutting edges, the router bit delivers high quality results for all your projects and a long working life.
This router bit can be used to work on most wood types or plastics. Thanks to the high quality finish of the bit, it is also possible to make grooves on different plastics such as acrylics (plexiglass), polycarbonate, polypropylene or PVC. To be used in router milling machines or CNC machines.
Set profielmessen hoogte 50mm Nr. 2072 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Set profielmessen hoogte 40mm Nr. 0017 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Content
Met behulp van deze balfrees maakt u snel en eenvoudig groeven voor schuifpanelen of elektrische bedrading. Dankzij de snijvlakken in hoogwaardig hardmetaal (widia) gebruikt u deze frees probleemloos op de meeste houtsoorten. Gebruik een rechte frees om een voorgroef te maken zodat de schacht van de balfrees zich vrij kan bewegen.
Deze set bestaat uit twee freeskoppen in lichtmetaal, uitgerust met hardmetalen messen (HW). Maak stevige verbindingen met behulp van de profiel- contraprofielfrees, of frees bossingen met de platbandfrees. Samen bieden deze twee freeskoppen u alles wat u nodig heeft om hoogwaardige, en mooi afgewerkte keukenkastdeuren te maken.
Standaard staat op de profiel- contraprofiel frees het profielmes type A gemonteerd. Op aanvraag zijn ook type B, C en D verkrijgbaar. Deze frees heeft een diameter van 120mm, voor meer informatie en alle technische gegevens zie art. ST-YH102AAM.
De bossingfrees bestaat uit twee messen die los van elkaar te verstellen zijn. Door de messen in verhouding van elkaar anders uit te lijnen, krijgt u de mogelijkheid om verschillende profielen te creëren, bijvoorbeeld met of zonder opstaande rand. Deze frees heeft een diameter van 183mm. De freeshoogte en snijlengte zijn afhankelijk van de manier waarop u de messen heeft ingesteld. Zie de extra informatie onderaan voor meer technische gegevens over deze frees.
Forstner drill bit with cylindrical shank for boring hinges with the best quality on every kind of wood or panels. This high quality hinge boring bit has two Tungsten cutting edges, two Tungsten spurs and a HW center point for boring with the best quality on every kind of wood or panels. Right hand boring only
Set profielmessen hoogte 40mm Nr. 0010 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Set profielmessen hoogte 40mm Nr. 0029 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Saw blade with 24 teeth
Multipurpose saw blade with WZ alternate top bevel teeth for quickly cutting along and across grain of all natural woods, wooden boarding materials or one sided veneer and plastic coated materials. For use on table saws. No noise saw blade with anti-kickback design.
Groefzaagblad met vlakke (FZ), widia zaagtanden om groeven te trekken in hardhout, zacht hout, gelamineerde panelen en andere producten op basis van hout. De zaagbladen hebben een asgat van 30mm en zijn ideaal voor gebruik op freesmachines of op zaagtafels.
Dit zaagblad is beschikbaar in verschillende diameters
Deze pneumatische vacuümtafel is ontworpen om gladde, niet poreuze werkstukken vast te klemmen. Het vacuüm tussen de basis van de tafel en het werkstuk zorgt voor een stevige klemming en laat na gebruik geen sporen na. Om de tafel vacuüm te maken dient ze aangesloten te zijn op een externe compressor (niet inbegrepen). Dankzij het compacte formaat is deze vacuümtafel zowel geschikt om in het atelier te gebruiken als daarbuiten. De tafel zelf moet bevestigd worden met behulp van schroeven in de voorziene gaten. Omdat u de tafel zowel verticaal als horizontaal kan plaatsen is deze module ideaal voor een brede waaier aan toepassingen. Klem werkstukken vast om te verlijmen, frezen, trimmen, etc...
Met behulp van de standaard geleverd rubber dichtingen verdeelt u de tafel eenvoudig in kleinere secties. Dit is erg handig om bijvoorbeeld kleine stukken vast te zetten. Om grotere werkstukken vast te zetten kan u meerdere modules gebruiken om doorzakken te voorkomen. Met het optionele verdeelblok (ref. 5046350) sluit u maximaal vijf pneumatische basismodules tegelijkertijd aan. Op deze manier kan u ze synchroon bedienen. Standaardlevering met één rubber dichting al geïnstalleerd en een transparante tube voor de luchttoevoer met 1/4" snelkoppeling.
Deze verstelbare afschuinfrees met snijvlakken in hoogwaardig hardmetaal, geeft u een enorme flexibiliteit bij het maken van schuine kanten. De frees is aan beide zijden instelbaar tussen 0° en 90° met stappen van 7,5°. Gebruik de frees zowel voor het afschuinen van hout als plaatmateriaal. Dankzij de hardmetalen messen snijdt deze groeffrees moeiteloos door massieve platen, harde en zachte houtsoorten, MDF of gelamineerde platen.
You can attach this accessory to the GuidePRO so that you can secure the GuidePRO in your miter slot. Ideal for repetitive and consistent cuts. The GuidePRO comes with a miter cam connector and is designed for quick set-ups and offers excellent feeding benefits for band saw cuts. Some GuidePRO users want the benefits of the GuidePRO, but as a fixed-position tool. The GuidePRO anchor bar locks the GuidePRO securely in place, so you don't have to move the tool with every cut.
GuidePRO Anchor Bar extends the use of the GuidePRO to the router table and table saw. The milling or sawing operation is different on a router or table saw than on the band saw where the blade moves down into the table. Bow Products requires the Miter Anchor to be used with the GuidePRO when used on the router or table saw to lock the tool in place for your safety and the safety of your tools. The GuidePRO Anchor Bar has two options for a left or right feed on these machines.
GuidePRO Anchor bar features and installation:
The GuidePRO anchor has an extendable 19 mm or ¾ inch miter bar with locking knobs. The anchor rod has slots for mounting on the GuidePRO base. Just use the included Allen key and unscrew the miter cam. Use the same screw to attach the anchor rod.
Note that the anchor rod has two mounting options for a left or right feed. Fit the selected Boss angle into the slot at the bottom of the GuidePRO base. Screw in place. The slot in the GuidePRO base allows the same positioning range for the GuidePRO to the fence.
Levage facile et sûr des panneaux de porte, meubles, ... Cet ascenseur de porte a une capacité de charge allant jusqu'à 200 kg. Équipé d'une base pivotante et d'une surface antidérapante. Fabriqué en aluminium. Hauteur maximale de levage 75cm.
Les presseurs Belmash offrent une sécurité accrue lorsque vous travaillez avec votre raboteuse. Planifiez en toute sécurité des poutres ou des planches sur n'importe quelle machine Belmash. La pince assure que la pièce est serrée sur la surface de travail. Cela facilite la circulation des matériaux, vous donnant une finition propre et précise. Ces dispositifs de serrage sont faciles à installer à l'aide des vis et des rondelles. L'ouverture peut être réglée à l'aide d'une poignée sur le dessus et d'une pince à ressort sur le côté. De cette manière, une bonne alimentation et une bonne force de pression sont toujours assurées.
Cette presseur peut être utilisé sur le Belmash SDMR2500.
Fraise à rainurer à lames réversibles et précouteaux en carbure de haute qualité (HW) pour réaliser des rainures de précision. Réglable progressivement en hauteur entre 28mm et 55mm. Grâce aux lames en carbure de tungstène, cette fraise à rainurer coupe sans effort les planches massives, les bois durs et tendres, le MDF ou les planches laminées.
Disponible avec un alésage de 30 mm ou 50 mm.
Avec les guides de stock de précision, vous n'avez plus à vous battre pour tenir des plaques ou des poutres tout en poussant sur la scie - et la table de fraisage. Les rouleaux tirent votre pièce en la plaçant fermement contre le guide et votre table de travail. Vous couperez de manière plus sûre, plus facile et plus précise tout en maintenant votre pièce en place à tout moment.
Rien ne peut vous donner plus de sécurité et de précision lorsque vous tenez votre pièce à usiner. Vous évitez le retour de bâton avec ça. Et ce sans limitation !
Les rouleaux de guidage uniques du Stock Guide sont inclinés à 5 degrés, ce qui permet de presser efficacement et régulièrement votre pièce contre le guide. Pour éviter le recul, chaque rouleau est équipé d'un roulement à billes qui ne peut tourner que dans un sens.
Votre pièce est poussée fermement contre le guide et la table de travail, et l'adhérence des rouleaux en polyuréthane la maintient en position en toute sécurité.
Les guides de stock de précision peuvent être fixés à un rail en T standard utilisé pour la plupart des tables de fraisage commerciales. Ils fonctionnent tout aussi bien sur un établi ou une table de perçage avec un rail en T de 1/4" sur le guide.
Les guides de crosse de précision sont fraisés par CNC à partir d'un aluminium robuste et anodisés pour leur apparence et leur durabilité. Les axes des roues sont en acier laminé à froid et trempé pour plus de durabilité. Les boutons de réglage sont en acier inoxydable pour durer. Les roues sont également fabriquées en plastique acétolique résistant à l'usure, ce qui leur confère une faible résistance au frottement. Les pneus antidérapants sont moulés en polyuréthane pour une longue durée de vie et une adhérence supérieure sur votre pièce.
Les guides de crosse ITAMAC Precision peuvent être installés facilement et rapidement. Le long du profil, vous pouvez les fixer dans n'importe quelle position en tournant les deux boutons. Vous pouvez régler la hauteur à l'aide du bouton de serrage. Lorsqu'ils ne sont pas utilisés, il suffit de les mettre de côté.
Set profielmessen hoogte 40mm Nr. 0061 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Forstner drill bit with cylindrical shank for boring hinges with the best quality on every kind of wood or panels. This high quality hinge boring bit has two Tungsten cutting edges, two Tungsten spurs and a HW center point for boring with the best quality on every kind of wood or panels. Right hand boring only
L'unité de rabotage est un outil indispensable pour le rabotage d'épaisseur sur le Belmash SDM2500 et permet d'obtenir une pièce d'excellente qualité. Il possède son propre bloc de coupe qui est entraîné par le moteur du SDM2500. Avec cet appareil, vous pouvez prévoir une épaisseur sur le SDM2500 de 5 à 103 mm et une largeur de rabotage de 250 mm.
Forstner drill bit with cylindrical shank for boring hinges with the best quality on every kind of wood or panels. This high quality hinge boring bit has two Tungsten cutting edges, two Tungsten spurs and a HW center point for boring with the best quality on every kind of wood or panels. Right hand boring only
READYtoWORK pakket van paneelzaag ITAMAC Maestro X7 3200mm inclusief afzuiginstallatie, afzuigslang, klembanden, montageklemmen etc. en set van hoofdzaagblad en voorritser voor afwerking plaatmateriaal. Formaatzagen met brede geanodiseerde aluminium roltafel op dubbele slijtvaste staafgeleiding met vervangbare rollers. Voorzien van een ingebouwde module start/stop systeem welke garant staat voor een optimaal gebruikscomfort.
Ces supports en acier à ressort galvanisé se montent au mur en quelques secondes et sont parfaits pour ranger des outils ou des accessoires d'un diamètre de 10 cm, tels que les nouveaux accessoires Air Flux. Les pièces de montage, le tuyau d'extraction flexible et d'autres outils avec un Ø 100 mm s'adaptent parfaitement ici.
Le Kreg Pocket-Hole Jig 720 Pro est le système de connexion professionnel, rapide et efficace avec des accessoires haut de gamme. Avec ce système, vous pouvez réaliser des trous de poche très résistants dans des matériaux d'une épaisseur minimale de 13 mm (1/2") et d'une épaisseur maximale de 38 mm (1 1/2").
Le Kreg 720 Pro est livré avec une station d'accueil. Cette extension offre plus de support pour des équipements plus volumineux et plus d'espace de stockage. Les pièces latérales de la station d'accueil peuvent être facilement pliées pour ranger le système lorsqu'il n'est pas utilisé. De plus, les pièces latérales peuvent également être déconnectées du système afin que vous puissiez créer encore plus de support pour votre pièce.
Avec la butée de matériau fournie, vous facilitez encore plus les travaux répétitifs. Vous glissez simplement la butée sur la pièce latérale de la station d'accueil et cela crée une stabilité supplémentaire pour votre pièce. Le bouchon de matériau peut être stocké dans la station d'accueil après utilisation.
La pince pour Pocket-Hole Jig en acier incluse est idéale pour fixer votre système de connexion à votre surface de travail. Cela en fait un système de connexion complet et professionnel pour votre établi. La pince est également facile à ranger dans la station d'accueil après utilisation.
La configuration du Kreg Jig 720 Pro est simple et rapide. Il vous suffit de placer votre matériau dans le gabarit et de pousser le levier vers le bas. Le système fait alors tout le travail pour vous et s'ajuste à la bonne épaisseur. Le levier vous donne également le contrôle complet de la force de serrage ! De plus, le système est doté d'un matériau antidérapant. Cela maintiendra votre pièce solidement en place sans marquer votre bois.
Vous pouvez mesurer l'épaisseur du matériau à l'aide de la jauge d'épaisseur fournie. Les dimensions suivantes y sont indiquées : 1/2”, 3/4” et 1 1/2” (13, 19 et 38 mm). Ces mesures correspondent aux mesures sur le foret étagé. Vous serrez la butée de perçage à la bonne taille avec la jauge d'épaisseur de matériau qui est également une clé Allen.
Au bas du Kreg 720 Pro se trouve un système de stockage intégré pour la perceuse, les embouts de vis et la jauge d'épaisseur de matériau. A côté de l'espace de stockage, les dimensions sont indiquées, avec plusieurs étapes intermédiaires. Cela vous permet d'ajuster la butée de perçage encore plus précisément sur le foret.
Le système de connexion Kreg 720 Pro est également livré avec une pièce d'extraction qui peut être fixée à gauche et à droite du gabarit de perçage. Un tuyau d'extraction peut alors être connecté à celui-ci. De cette façon, la poussière et les copeaux de bois sont aspirés et vous continuez à avoir une bonne vue sur votre surface de travail. Cela rend les trous de poche beaucoup plus efficaces.
Le système de connexion Kreg peut être utilisé horizontalement et verticalement. De cette façon, vous pouvez faire des trous de poche comme vous le souhaitez.
Comme vous en avez l'habitude chez Kreg, ce système est également basé sur la durabilité. Grâce à la construction en plastique résistant aux chocs et durable avec un noyau en acier trempé, vous pouvez être assuré que le système durera.
Le 720 Pro est livré avec 160 vis Pocket-Hole dans les deux tailles les plus populaires. Vous recevrez également un plan de projet. Vous pouvez donc commencer tout de suite!
Set profielmessen hoogte 50mm Nr. 2010 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Structure brush machine for wood metal and stone.
The DUROTEC textured brush machine is a master of brushing, satinising, sanding and polishing. The brushes mainly remove the softer wood of the more recent growth rings and leave the harder wood of the older growth rings intact. The wood is thus artificially aged, as the mechanical processing considerably accelerates the natural weathering effect. Brushed wooden surfaces are used, among other things, in the manufacture of rustic furniture, the furnishing of rustic cafés and restaurants (wall and ceiling coverings) or for beams.
The Durotec brushing machine is the ideal machine for rust removal from metal surfaces, oxidation removal, polishing of metal surfaces, finishing steel, stainless steel, and non-ferrous metals, etc.
The new brushing machine is more powerful and compact and can run even slower for a better finish. The double transmission ensures that you can apply pressure without slowing down the machine for extra correction power. The ergonomic design and low weight make this machine perfect to handle for brushing or structuring your workpiece. Equipped with a robust handle which is adjustable in height.
Fonctionne avec toutes les machines jusqu'à 7,5 KW. Connecter plusieurs machines afin qu'elles puissent être mises en marche ensemble. Utilisez ce démarreur simultané lorsque vous combinez une machine à bois et un système de dépoussiérage. Le moteur de démarrage assure le démarrage automatique de votre aspirateur quatre secondes après que vous ayez vous-même mis en marche votre machine à bois. Après avoir arrêté votre machine à bois, l'extraction est également arrêtée quelques secondes plus tard. Ces quelques secondes supplémentaires d'aspiration garantissent que vos tuyaux sont toujours propres.
Bandsaw blade with length 3607mm for use on the TT500X band saw machine from Tendotools. This saw blade has 3 TPI (teeth per inch) and has a width of 25mm. This bandsaw blade in tempered steel "Flexback" is very suitable for multipurpose sawing. Use this saw ribbon for both wood and plastics. The teeth of the saw blade were given an additional heat treatment for increased hardness. This keeps the band very supple and increases your cutting comfort thanks to the hardness of the teeth.
Extra afvalzakken in PVC 120µm voor gebruik met de stofafzuigingen van Air Flux. Deze zakken kunnen gebruikt worden met de Air Flux Dusty 1020AF.
Les dents de cette lame de scie sont aiguisé en forme de V (45°) pour facilement et rapidement faire des rainures dans votre lambris. Sur demande, les dents peut être aussi aiguiser en différents formes/angles ou avec des épaisseurs différents.
Lame de scie pour rainues avec denture widia en forme V pour faire des rainures dans des bois durs, tendres, exotiques et des panneaux avec revêtement en plastique. Les lames de scie ont un alésage de 30mm et sont idéal à utiliser sur des toupies ou des scies à table.
Tenoning jig TJ-85 for the Itamac Panthera (Harvest) HW110SE table saws.
Ideal for sawing tenons etc.
Straight router bits are specifically designed for making grooves in most types of wood or several plastics. Together with two straight cutting edges, there is a special tip on the bottom (Z=2+1) which allows easy and precise boring. The router bit is solid carbide, with special micrograin finishing for best performance. Thanks to these combined qualities the router bit delivers high quality results for all your projects and a long working life. This router bit can be used to work on most wood types or plastics. Thanks to the high quality finish of the bit, it is also possible to make grooves on different plastics such as acrylics (plexiglass), polycarbonate, polypropylene or PVC. To be used in router milling machines or CNC machines.
Forstner drill bit with cylindrical shank for boring hinges in most wood types or panels. This high quality hinge boring bit has two Tungsten cutting edges, two Tungsten spurs and a HW center point for boring with the best quality on every kind of wood or panels. Right hand boring only
This boring bit is available in two lengths
Convenient all in one set to make dovetail joints with the Virutex PL11. The set includes an interchangeable PVC mould with tooth spacing (pas) 34mm, an adapted guide ring Ø23mm and the correct dovetail bit Ø19mm. Use this set to make large dovetail joints (e.g. for furniture). Minimum thickness of the wood to be able to work correctly is 24mm.
This guide rail can be used as an extension for the rail which is delivered as a standard wih the plunge-cut saws TT55 and TT85.
Available in lengths 800 mm or 1400 mm.
You need the connection kit to assemble this extension.
Set de couteaux profilés hauteur 40mm Nr. 0064 pour des porte-outils à profiler universels. Approprié pour le fraisage de profilés de chants en bois massif avec un faible coût d'outillage. Acier à outils allié avec 16% cobalt pour un qualité de coup très haut et un fraisage confortable.
Ø 100mm Keyed hose clamps have a thumbscrew that allows you to quickly tighten or loosen without a screwdriver or wrench. Makes setting up, modifying or cleaning your dust collection system easier! For use with Ø 100 mm extraction hoses and connectors.
Set of 5 pieces.
Joint isolant en silicone pour fenêtres et portes de couleur blanche. Excellente résistance à des températures comprises entre -60 et 200°C. Avec ce sceau, vous bénéficierez à la fois d'une bonne isolation température et d'une bonne isolation acoustique. Essentiel pour les nouvelles constructions et facile à intégrer dans les constructions existantes. Utilisez la rainureuse Virutex RA17VG avec le mèche ancre double.
Disponible en diamètre 6mm ou 8mm.
Koppelstuk 45° met diameter 100mm om te gebruiken in combinatie met de Air Flux stofafzuigingssystemen.
Set de couteaux profilés hauteur 40mm Nr. 0026 pour des porte-outils à profiler universels. Approprié pour le fraisage de profilés de chants en bois massif avec un faible coût d'outillage. Acier à outils allié avec 16% cobalt pour un qualité de coup très haut et un fraisage confortable.
Straight router bits are specifically designed for making grooves in most types of wood or several plastics. These router bits are finished with carbide cutting edges. Thanks to the carbide cutting edges, the router bit delivers high quality results for all your projects and a long working life.
This router bit can be used to work on most wood types or plastics. Thanks to the high quality finish of the bit, it is also possible to make grooves on different plastics such as acrylics (plexiglass), polycarbonate, polypropylene or PVC. To be used in router milling machines or CNC machines.
The TT255SL is a mitre saw with pull function and the little sister of the TT305SLX. It is equipped with a noiseless 1600 W induction motor that requires no maintenance (which is a big advantage over the carbon brush motor in the smaller models) and has a pull function up to 300 mm, with a cutting height up to 60 mm.
The use of ball bearings on all joints ensures precise rotation of the table, head and tilting system. The saw has a die-cast aluminum body. The silent, maintenance-free 1600 W induction motor with belt drive delivers 30% more power and is 40% more silent than a carbon brush motor. The saw blade has a 255 mm diameter and 40 teeth. The turntable has an automatic and manual stop. The mitre indication is clear and tiltable.
The TT255SL is further equipped with a horizontal handle with control on the protective cover.
Klein® trimming bits with straight cut are suitable for smooth and well-finished edges on melamine and veneered panels. The ball bearing, having the same diameter of the cutters, trims any overlap leaving a flat and smooth edge. Two flutes provide fast cutting and good chipping ejection.
Fraises à rainurer sont spécifiquement conçue pour faire des rainures dans des types de bois différents ou des plastiques. Ces fraises sont fournis de faces de coupe en carbide. Grâce à ces faces de coupe en carbide le fraise vous assure un résultat parfait de tous votre projets ét une longue durée de vie.
Ce fraise peut être utiliser avec le plupart de types de bois. Grâce a la qualité extraordinaire il est aussi possible d'utiliser les fraises sur les plastiques comme l'acrylat (Plexiglas), polycarbonate, polypropylène ou de PVC. A utiliser dans des défonceuses ou des machines CNC.
Set profielmessen hoogte 40mm Nr. 0080 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Foret forstner avec queue cylindrique pour percer des charnières invisibles dans le plupart des bois ou panneaux. Cette mèche charnière de haute qualité avec pointe de centrage, deux faces de découpage en widia et deux guides en widia vous assure une finition parfait de tous vos trous. Rotation à droite uniquement.
Lamelles par boîte 1000 pièces. Fabriqué à partir de bois européens de haute qualité. Grâce à sa structure extra absorbante.
Set profielmessen hoogte 40mm Nr. 0003 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Cette table à vide électrique sur pied basculant est conçue pour serrer des pièces lisses et non poreuses. Le vide entre la base de la table et la pièce à usiner assure un serrage ferme et ne laisse aucune trace après utilisation. Pour que la table soit à vide, elle doit être connectée au système de fixation électrique à vide SVE600 de Virutex (inclus en standard). Grâce à sa taille compacte, cette table à vide peut être utilisée aussi bien dans l'atelier qu'à l'extérieur. La tête du support peut s'incliner de 90° afin que vous puissiez placer la pièce dans une position idéale. De plus, la plaque supérieure peut être tournée à 360°. Le support doit être fixé à l'aide de pinces (non comprises). Comme vous pouvez placer la table à la fois verticalement et horizontalement, ce module est idéal pour un large éventail d'applications. Pièces de serrage pour le collage, le fraisage, l'ébavurage, etc...
En utilisant les joints en caoutchouc fournis en standard, vous pouvez facilement diviser le tableau en sections plus petites. C'est très utile pour sécuriser les petites pièces, par exemple. Pour sécuriser des pièces plus importantes, le support auxiliaire SVE680 est disponible en option. Ce support est spécialement conçu pour se connecter au modèle SVE660 ou SVE670. Livraison standard avec un joint en caoutchouc déjà installé.
Top table à utiliser sur la base mobile Belmash. En utilisant la top table, la machine peut être placée séparément sur la base mobile afin que vous puissiez facilement l'emporter avec vous dans la voiture. La top table peut être utilisée en combinaison avec la base mobile PK2 et est suffisamment grande pour accueillir les modèles Universal 2000, SDM2500, SDMR2500 ou SDR2200. Fabriqué en métal avec un bord relevé. Il peut être installé sur une base mobile avec bord relevé vers le bas ou vers le haut.
Bandsaw blade with length 2240mm for use on the TT312 band saw machine from Tendotools. This saw blade has 6 TPI (teeth per inch) and has a width of 6mm. This bandsaw blade in tempered steel "Flexback" is very suitable for multipurpose sawing. Use this saw ribbon for both wood and plastics. The teeth of the saw blade were given an additional heat treatment for increased hardness. This keeps the band very supple and increases your cutting comfort thanks to the hardness of the teeth.
Forstner drill bit with cylindrical shank for boring hinges with the best quality on every kind of wood or panels. This high quality hinge boring bit has two Tungsten cutting edges, two Tungsten spurs and a HW center point for boring with the best quality on every kind of wood or panels. Right hand boring only
This extension can be placed on the left or right side of the Virutex table MT58K. Work easily with longer pieces on your table.
Guide rail or jig for circles and ovals with maximum diameter and main axis 3200mm. This compass is ideal for making mirrors, windows, doors, or any other creation with a circular or elliptical shape. To mill out an elliptical shape, use both swivel supports and elongated guides. By using just one of the two swivel supports you can mill perfect circles. Place the support exactly in the centre of the mould to make circles.
The guide rail is equipped with two powerful suction cups to attach to your panels without damage. If it is not possible to use the suction cups (e.g. on porous materials), the mould is provided with holes to screw them on. Standard delivery with two rods (Ø8mm) to attach the router to the guide.
Straight router bits are specifically designed for making grooves in most types of wood or several plastics. These router bits are finished with carbide cutting edges. Thanks to the carbide cutting edges, the router bit delivers high quality results for all your projects and a long working life.
This router bit can be used to work on most wood types or plastics. Thanks to the high quality finish of the bit, it is also possible to make grooves on different plastics such as acrylics (plexiglass), polycarbonate, polypropylene or PVC. To be used in router milling machines or CNC machines.
Straight router bits are specifically designed for making grooves in most types of wood or several plastics. Together with two straight cutting edges, there is a special tip on the bottom (Z=2+1) which allows easy and precise boring. These router bits are finished with carbide cutting edges. Thanks to the carbide cutting edges, the router bit delivers high quality results for all your projects and a long working life.
This router bit can be used to work on most wood types or plastics. Thanks to the high quality finish of the bit, it is also possible to make grooves on different plastics such as acrylics (plexiglass), polycarbonate, polypropylene or PVC. To be used in router milling machines or CNC machines.
The BOW FeatherPRO featherboard features an innovative use of high-density EVA Foam / foam combs and clamping system that increase control of insertion, dramatically improve recoil and protects your wood better from damage. This compared to the general plastic feaherboards. EVA is a high density, closed cell material with long life that you don't have with the common plastic featherboards. Ideal for table saws, routers, guides
Straight router bits are specifically designed for making grooves in most types of wood or several plastics. These router bits are finished with carbide cutting edges. Thanks to the carbide cutting edges, the router bit delivers high quality results for all your projects and a long working life.
This router bit can be used to work on most wood types or plastics. Thanks to the high quality finish of the bit, it is also possible to make grooves on different plastics such as acrylics (plexiglass), polycarbonate, polypropylene or PVC. To be used in router milling machines or CNC machines.
Set profielmessen hoogte 50mm Nr. 2072 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Set profielmessen hoogte 40mm Nr. 0017 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Weight
0,05 kg
1 kg
0,05 kg
0,05 kg
0,05 kg
1 kg
1 kg
0,325 kg
1 kg
0,6 kg
1,1 kg
3,3 kg
1 kg
5 kg
0,05 kg
0,05 kg
16,5 kg
0,05 kg
900 kg
0,2 kg
3 kg
0,05 kg
3 kg
1 kg
0,5 kg
0,5 kg
1 kg
5 kg
0,05 kg
0,05 kg
0,5 kg
5 kg
0,05 kg
0,2 kg
2 kg
0,5 kg
0,05 kg
0,05 kg
20 kg
0,05 kg
0,05 kg
0,05 kg
0,05 kg
2 kg
0,05 kg
1 kg
5,75 kg
0,5 kg
0,05 kg
1 kg
3 kg
0,05 kg
0,05 kg
1 kg
0,05 kg
0,05 kg
0,05 kg
Dimensions
N/B
N/B
N/B
0,4 cm
0,4 cm
N/B
N/B
16 × 20 × 2,2 cm
N/B
N/B
N/B
30 × 26 × 7 cm
N/B
N/B
0,4 cm
N/B
N/B
N/B
N/B
N/B
N/B
0,5 cm
38 cm
N/B
N/B
N/B
N/B
N/B
N/B
N/B
N/B
N/B
0,4 cm
N/B
N/B
N/B
0,4 cm
N/B
630 × 450 × 490 cm
N/B
N/B
0,4 cm
N/B
N/B
0,4 cm
N/B
625 × 360 × 27 cm
N/B
N/B
N/B
N/B
N/B
N/B
N/B
N/B
0,5 cm
0,4 cm
Additional information
Gewicht
0,05 kg
Diameter
19mm
Diameter 2
8,5mm
Lengte
64mm
Radius
R9,5
Schacht
12mm
Snijvlakken
2
Gewicht
1 kg
Diameter
183mm
As diameter
30mm
Freeshoogte
30mm
Snijvlakken
2+2
Snijlengte
60mm
Toerental Min-Max
4100-7000
Gewicht
0,05 kg
Diameter
55mm
Lengte
90mm
Schacht
10x60mm
Gewicht
0,05 kg
Afmetingen
0,4 cm
Gewicht
0,05 kg
Afmetingen
0,4 cm
Gewicht
1 kg
Zaagblad diameter
250mm
As diameter
30mm
Tand dikte
3,2mm
Zaagblad dikte
2,2mm
Aantal tanden
24
Meeneemgaten
PH02
Gewicht
1 kg
Zaagblad diameter
125mm, 150mm
As diameter
30mm
Tand dikte
1,5mm
Zaagblad dikte
1,1mm
Aantal tanden
12, 18
Gewicht
0,325 kg
Afmetingen
16 × 20 × 2,2 cm
Afmetingen werkvlak
150x150mm
Vacuumkracht
800gr/cm² bij 6 bar
Werkdruk
5,5-7 bar
Luchtverbruik bij 5,5 bar
28l/min
Gewicht
1 kg
Diameter
140mm
As diameter
30mm
Snijvlakken
2
Freeshoogte
50mm
Toerental Min-Max
5000-7500
Gewicht
0,6 kg
Gewicht
1,1 kg
Laad capaciteit
100kg
Gewicht
3,3 kg
Afmetingen
30 × 26 × 7 cm
Max. hoogte werkstuk
63mm
Max. breedte werkstuk
270mm
Gewicht
1 kg
Diameter
160mm
As diameter
30mm, 50mm
Snijvlakken
4
Aantal tanden
4
Snijlengte
44mm
Freeshoogte
28-55mm
Toerental Min-Max
4800-8200
Gewicht
5 kg
Gewicht
0,05 kg
Afmetingen
0,4 cm
Gewicht
0,05 kg
Diameter
19mm
Lengte
90mm
Schacht
10x60mm
Gewicht
16,5 kg
Vandikte capaciteit
5-103mm
Aantal messen
2
Schaafbreedte
250 mm
Gewicht
0,05 kg
Diameter
21mm
Lengte
90mm
Schacht
10x60mm
Gewicht
900 kg
Gewicht
0,2 kg
Diameter
100mm
Gewicht
3 kg
Schacht boor
6,35 mm
Boordiameter
9,5 mm
Min. materiaaldikte
13 mm
Max. materiaaldikte
38 mm
Gewicht
0,05 kg
Afmetingen
0,5 cm
Gewicht
3 kg
Afmetingen
38 cm
Voltage
230 V
Vermogen
800W
Toerental Min-Max
1200-3900
Borstel
110x115x19mm
Gewicht
1 kg
Gewicht
0,5 kg
Lengte
3607mm
Breedte
25mm
Dikte
0,85mm
Gewicht
0,5 kg
Gewicht
1 kg
Zaagblad diameter
150mm
As diameter
30mm
Tand dikte
6,0mm
Zaagblad dikte
4,0mm
Aantal tanden
18
Tand vorm
Aangeslepen V-tand
Gewicht
5 kg
Gewicht
0,05 kg
Diameter
8mm
Snijlengte
32mm
Lengte
63mm
Snijvlakken
2+1
Gewicht
0,05 kg
Diameter
26mm
Lengte
90mm, 120mm
Schacht
10x100mm, 10x60mm
Gewicht
0,5 kg
Gewicht
5 kg
Lengte
800 mm, 1400 mm
Gewicht
0,05 kg
Afmetingen
0,4 cm
Gewicht
0,2 kg
Diameter
98-105mm, 100mm
Gewicht
2 kg
Diameter
6mm, 8mm
Gewicht
0,5 kg
Diameter
100mm
Gewicht
0,05 kg
Afmetingen
0,4 cm
Gewicht
0,05 kg
Diameter
10mm
Snijlengte
19mm, 25mm, 32mm
Lengte
51mm, 57mm, 63mm
Snijvlakken
2
Gewicht
20 kg
Afmetingen
630 × 450 × 490 cm
Max. zaagdikte
60 mm
Vermogen
1600 W
Snede 0° x 0°
300 x 60 mm
Snede 0° x 45°
212 x 60 mm
Snede 45° x 0°
300 x 50 mm
Snede 45° x 45°
212 x 50 mm
Zaagblad diameter
255 mm
Gewicht
0,05 kg
Diameter
12,7mm
Snijlengte
13mm
Lengte
54mm
Snijvlakken
2
Gewicht
0,05 kg
Diameter
12mm
Snijlengte
25mm
Lengte
70mm
Schacht
12mm
Snijvlakken
2
Gewicht
0,05 kg
Afmetingen
0,4 cm
Gewicht
0,05 kg
Diameter
24mm
Lengte
90mm
Schacht
10x60mm
Gewicht
2 kg
Type lamel
Nr. 20
Gewicht
0,05 kg
Afmetingen
0,4 cm
Gewicht
1 kg
Vermogen
95W
Afmetingen werkvlak
150x150mm
Vacuümdruk
750mbar
Gewicht
5,75 kg
Afmetingen
625 × 360 × 27 cm
Gewicht
0,5 kg
Lengte
2240mm
Breedte
6mm
Dikte
0,65mm
Gewicht
0,05 kg
Diameter
32mm
Lengte
90mm
Schacht
10x60mm
Gewicht
1 kg
Gewicht
3 kg
Minimum kleine as (ellips)
600mm
Maximum grote as (ellips)
3200mm
Minimum diameter (cirkel)
600mm
Maximum diameter (cirkel)
3200mm
Gewicht
0,05 kg
Diameter
21mm
Snijlengte
19mm
Lengte
51mm
Snijvlakken
2
Gewicht
0,05 kg
Diameter
12mm
Snijlengte
19mm, 25mm
Lengte
51mm, 57mm
Snijvlakken
2+1
Gewicht
1 kg
Gewicht
0,05 kg
Diameter
25mm
Snijlengte
19mm
Lengte
51mm
Snijvlakken
2
Gewicht
0,05 kg
Afmetingen
0,5 cm
Gewicht
0,05 kg
Afmetingen
0,4 cm
Meld je aan voor onze nieuwsbrief
Select the fields to be shown. Others will be hidden. Drag and drop to rearrange the order.
Image
SKU
Rating
Price
Stock
Availability
Add to cart
Description
Content
Weight
Dimensions
Additional information
Click outside to hide the comparison bar
Vergelijken
We gebruiken cookies om ervoor te zorgen dat onze website zo soepel mogelijk draait. Als je doorgaat met het gebruiken van de website, gaan we er vanuit dat je ermee instemt.OkPrivacy policy