Deze transporthendel is standaard voorzien van een klem waardoor deze hendel geschikt is voor meerdere functies. Inzetbaar als kantenpers, hoekpers of transporthendel. Dankzij het ontwerp in aluminium is deze hendel erg sterk en robuust. De maximale last bedraagt 70kg. Als kantenpers kan u de PC81U zowel gebruiken op rechte panelen, als op holle of bolle panelen. Als hoekpers wordt deze hendel dan weer de ideale tool om bijvoorbeeld kaders te maken. De klem is afneembaar en door de handgreep van positie te veranderen is de PC81U eenvoudig om te bouwen tot transporthendel. Geschikt voor panelen van dikte tussen 0mm en 46mm.
Voor het verbinden van panelen van 16 of 19mm dikte met behulp van deuvels (Ø8mm) of schroeven. Werk met een hoge precisie & hoogkwalitatieve afwerking, zonder de nood om achteraf bij te stellen. Deze positiegeleider is zowel geschikt om gaten te boren op de kopse kant, langsheen de zijkant, of op elke positie in het midden van het paneel. Maximumbreedte van het paneel om de geleider te plaatsen is 630mm. Standaardlevering met inzetstukken voor planken van 16 mm, verloopringen en boorstop.
Quarter-circle concave radius cutter to easily and quickly round corners. Increasing the working depth, you will obtain the classical "quarter-round" typical of dining table edges. Perfect finish of your project on different wood types thanks to the HW tungsten cutting edges.
Equipped with a ball bearing for easier work. When using a bit with a large radius, it is advisable to carry out the machining in several steps.
Kreg assortment case with the six most commonly used screws. There are 30 or 50 of each screw in an assortment case.
The case contains four lengths of screws for softwood and one length for hardwood. The fifth screw is blue and has a triple coating, making it corrosion resistant. It can therefore be used both outdoors and indoors in damp rooms.
Contents:
- 50x SPS-C1 1" (25 mm)
- 50x SML-F125 1 1/4" (32 mm)
- 50x SML-C125 1 1/4" (32 mm)
- 50x SML-C150 1 1/2" (38 mm)
- 30x SML-C250 2 1/2" (64 mm)
- 30x SML-C250B 2 1/2" (64 mm)
Quarter-circle concave radius cutter to easily and quickly round corners. Increasing the working depth, you will obtain the classical "quarter-round" typical of dining table edges. Perfect finish of your project on different wood types thanks to the HW tungsten cutting edges.
Equipped with a ball bearing for easier work. The smaller bearing provides an upright standing side to the rounding. When using a bit with a large radius, it is advisable to carry out the machining in several steps.
Tweemaal uitgang Ø125mm voor gebruik met de Air Flux Cyclone stofafzuigingen. De grote diameter is 203mm, rechtstreeks aansluitbaar op de cycloon afzuiggroepen, met vertakkingen naar 2x125mm.
Replacement waste bags PVC 120µm to be used with the Air Flux dust extractors. These bags are compatible with the Air Flux Dusty 1020AF.
Specially designed hand gluer for gluing large surfaces with vinyl (white) adhesives. Available in two models with different roll widths and glue container capacities. Model EM26D is equipped with a roll with a width of 122mm and a capacity of 1kg. The larger model EM126D has a roll with a width of 180mm and a capacity of 1.4kg. The machine is equipped with a trigger on the handle for easy opening and closing of the glue container. At the top there is a second roller (width 92mm) for stationary glueing along the top with the machine.
Attention: this hand gluer comes standard with a rubber roller, suitable for vinyl (white) adhesives and water-based adhesives. For synthetic adhesives an optional PU roll is available (Ref. 2504065). This hand gluer is also available without roller at the top (models EM26D and EM126T).
Square carbide plaque for roughing gouge 11 mm
Set profielmessen hoogte 40mm Nr. 0046 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Groefzaagblad met vlakke (FZ), widia zaagtanden om groeven te trekken in hardhout, zacht hout, gelamineerde panelen en andere producten op basis van hout. De zaagbladen hebben een asgat van 30mm en zijn ideaal voor gebruik op freesmachines of op zaagtafels.
Dit zaagblad is beschikbaar in verschillende diameters
Set profielmessen hoogte 50mm Nr. 2004 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Saw blade with 36 teeth
Saw blade with alternate top bevel teeth, chip breakers and anti-kickback design. With few teeth for a rough and fast cut of the wood. Equipped with teeth in high quality carbide (widia). Suitable for both shortening and longitudinal cutting of hard and soft types of wood. Can also be used for sawing chipboard or single-sided laminated wood. Ideal for construction site saws or tilting log saws. Made in Germany, take advantage of the extremely solid German quality.
Set profielmessen hoogte 40mm Nr. 0007 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Set profielmessen hoogte 40mm Nr. 0048 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Set of profile knives of height 40mm Nr. 0087 suited for universal moulding blocks. Used for moulding of wood at low costs. The steel alloy with 16% cobalt guarantees a high quality cut and a comfortable cutting process.
Deze frees is geschikt voor het maken van zwaluwstaartverbindingen. Zwaluwstaartverbindingen zijn klassieke, maar ijzersterke mechanische verbindingen om te gebruiken in houtbewerking. Gebruik deze verbindingen om kasten, lades, kisten of andere hoekverbindingen te vervaardigen. Dankzij de hardmetalen (widia) snijvlakken is een precieze en nette afwerking van uw freeswerken te allen tijde gegarandeerd.
Om sneller en efficiënter te werken kan u gebruik maken van een mal voor zwaluwstaartverbindingen.
Reducer diameter 100-50mm to be used with the Air Flux dust extractors.
Verlengstukken voor de wielkit WK600. Gebruik de twee staven (lengte: 915mm) om de originele uit uw wielkit te vervangen. Vervoer grotere machines zonder verlies van draagkracht.
SHOWROOM MODEL - NIEUW
exclusief boortafel
Krachtige, robuust vlak- en vandiktebank met inductiemotor, geschikt voor elke werkplaats. Deze machine is verkrijgbaar met een motor op 230V of drie fasen 400V. Dankzij het stevige, stalen design met gietijzeren werkbladen is deze machine bestand tegen zwaar dagelijks gebruik. De werktafels zijn onderaan voorzien van een zwaar profiel om de vlakheid te allen tijde te behouden. De tafels scharnieren onafhankelijk van elkaar en kunnen omhoog geplaatst worden. Om erg precies te kunnen schaven is deze machine bovenaan voorzien van een stevige, aluminium geleider. Deze geleider kan ingesteld worden onder hoek met twee stops voor 90° en 45°.
Standaard is deze machine voorzien van schaafbeitels met een dikte van 1,5mm. Dikkere schaafbeitels (3mm) zijn verkrijgbaar op aanvraag.
Fraises à rainurer sont spécifiquement conçue pour faire des rainures dans des types de bois différents ou des plastiques. Grâce au face de coupe supplémentaire en bout de fraise (Z=2+1), c'est aussi possible de facilement faire de perçage.
Ce fraise peut être utiliser avec le plupart de types de bois. Grâce a la qualité extraordinaire il est aussi possible d'utiliser les fraises sur les plastiques comme l'acrylat (Plexiglas), polycarbonate, polypropylène ou de PVC. A utiliser dans des défonceuses ou des machines CNC.
Straight router bits are specifically designed for making grooves in most types of wood or several plastics. These router bits are finished with carbide cutting edges. Thanks to the carbide cutting edges, the router bit delivers high quality results for all your projects and a long working life.
This router bit can be used to work on most wood types or plastics. Thanks to the high quality finish of the bit, it is also possible to make grooves on different plastics such as acrylics (plexiglass), polycarbonate, polypropylene or PVC. To be used in router milling machines or CNC machines.
Klein® trimming bits with straight cut are suitable for smooth and well-finished edges on melamine and veneered panels. The ball bearing, having the same diameter of the cutters, trims any overlap leaving a flat and smooth edge. Two flutes provide fast cutting and good chipping ejection.
Set profielmessen hoogte 40mm Nr. 0037 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Works with all machines up to 7.5 KW. Connect several machines so that they can be started up together. Use this simultaneous starter when combining a woodworking machine and dust extractor. The starter motor ensures that your dust extraction system starts up automatically four seconds after you start up your woodworking machine yourself. After stopping your woodworking machine, extraction is also stopped a few seconds later. These extra few seconds of suction ensure that your pipes are always clean.
Straight router bits are specifically designed for making grooves in most types of wood or several plastics. Together with two straight cutting edges, there is a special tip on the bottom (Z=2+1) which allows easy and precise boring. This router bit can be used to work on most wood types or plastics. Thanks to the high quality finish of the bit, it is also possible to make grooves on different plastics such as acrylics (plexiglass), polycarbonate, polypropylene or PVC. To be used in router milling machines or CNC machines.
ShowroommodelMET GRATIS ACCESSOIRES:+ FREESAS VOOR BOVENFREZEN 8, 10 & 12 MM+ EXTRA FREESAS 20 MM+ VERRIJDBAAR ONDERSTEL+ VERSTEKGELEIDER
De Itamac Eagle series zijn hoogwaardige freesmachines, specifiek ontwikkeld voor professionele freestoepassingen. Ontworpen met het oog op zowel functionaliteit als comfort, beschikt deze machine over alle mogelijke functies voor een freesmachine uit deze klasse. Voorzien van een extra zwaar chassis, een massief gietijzeren beschermkap met aluminium geleiders en fijnregeling. De krachtige 230V motor levert 3PK en zorgt ervoor dat deze tafel bijna elke freesopdracht aankan. De Itamac Eagle HW300E heeft een as van 30mm. Mits de optioneel verkrijgbare frees as en spantangen kan de machine ook ingezet worden om te profileren met behulp van bovenfrezen. De grote gietijzeren tafel garandeert de nodige stabiliteit tijdens het werken. Inzetbaar op vier snelheden, met gecentraliseerd controlepaneel boven de machine.
Fraises à rainurer sont spécifiquement conçue pour faire des rainures dans des types de bois différents ou des plastiques. Grâce au face de coupe supplémentaire en bout de fraise (Z=2+1), c'est aussi possible de facilement faire de perçage. Ces fraises sont fournis de faces de coupe en carbide. Grâce à ces faces de coupe en carbide le fraise vous assure un résultat parfait de tous votre projets ét une longue durée de vie.
Ce fraise peut être utiliser avec le plupart de types de bois. Grâce a la qualité extraordinaire il est aussi possible d'utiliser les fraises sur les plastiques comme l'acrylat (Plexiglas), polycarbonate, polypropylène ou de PVC. A utiliser dans des défonceuses ou des machines CNC.
Bandsaw blade with length 3607mm for use on the TT500X band saw machine from Tendotools. This saw blade has 4 TPI (teeth per inch) and has a width of 13, 16 or 20mm. This bandsaw blade in tempered steel "Flexback" is very suitable for multipurpose sawing. Use this saw ribbon for both wood and plastics. The teeth of the saw blade were given an additional heat treatment for increased hardness. This keeps the band very supple and increases your cutting comfort thanks to the hardness of the teeth. Thickness of 0,80mm, the saw ribbon of 13mm has a thickness of 0,65mm.
Light and powerful sander for sanding all types of surfaces. The ergonomic design ensures a perfect grip and comfortable working. Thanks to the perfect balancing, you can enjoy a reduced vibration level. Equipped with a large polyurethane sanding base (93x185mm). Because of these dimensions, the sanding base prevents the metal parts from damaging corners or edges during accurate work. On the other hand, the sanding surface is still perfectly suitable for sanding narrow surfaces, e.g. between mouldings. Equipped with an integrated dust extractor and dust bag.
Set profielmessen hoogte 40mm Nr. 0057 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
The thicknessing unit is an indispensable tool for planing on the Belmash SDM2500 and makes it possible to obtain a workpiece of excellent quality. It has its own cutterblock that is driven via the motor of the SDM2500. With this unit you can plan thickness on the SDM2500 of 5-103mm and a planing width of 250mm.
Set profielmessen hoogte 40mm Nr. 0071 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Set profielmessen hoogte 40mm Nr. 0069 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Schuurband voor schuurmachine TT915 - 915 x 100 mm
Adapter ring to reduce the bore of your saw blade to comply with your machine. Make sure every saw blade is compatible with your own machine thanks to these convenient reduction rings.
Reduction from bore 20mm to 12,7mm.
This chisel allows you to make sharp narrows and hollow out rounded surfaces straight. Is ideally suited for sizing diameters when turning between centers.
Conçu pour percer les panneaux afin d'y insérer des chevilles en bois pour l'assemblage des panneaux. Equipé d'une butée micrométrique réglable pour toutes les hauteurs et tous les angles. Positionnement de la machine par butées rétractables et références visuelles à 32 mm (standard). Double alésage pour des connexions rapides et précises. Réglage facile pour toute épaisseur de panneau et réglage variable pour la bonne profondeur de perçage. Équipé d'un raccord externe pour le dépoussiérage et fourni avec une mallette de transport pratique et empilable.
Moteur puissant avec contrôle électronique pour maintenir une vitesse constante sous charge. MAINTENANT AUSSI GRATUIT 100 pcs OVVO PERMANENT CHEVILLES Ø 8 mm
NO GLUE - NO TOOLS - ULTRA STRONG
Télécharger la promotion PDF
Cette base mobile de Belmash est compatible avec les machines Universal 2000, SDM2500, SDMR2500 et SDR2200. Placez votre machine Belmash à une hauteur idéale et rendre mobile.
Vane d'arrêt murale, diamètre 100 mm, à utiliser en combinaison avec les systèmes d'extraction de poussière Air Flux.
Pistolet à air chaud avec contrôle électronique de la température et deux réglages de chaleur. Cela vous permet de toujours adapter l'outil au travail que vous faites. Ce pistolet thermique est très adapté pour former ou souder des plastiques, travailler avec des autocollants/films, rétracter des fils de fer et bien plus encore. Livraison standard avec une buse. De plus, ce pistolet thermique est compatible avec la plupart des accessoires actuellement disponibles sur le marché.
Set profielmessen hoogte 50mm Nr. 2009 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Set profielmessen hoogte 50mm Nr. 2005 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Antistatische afzuigslang lengte 6 meter diameter 100 mm. Te gebruiken in combinatie met de stofafzuigingen van Air Flux.
Cutter head in light alloy with reversible blades in high quality tungsten carbide (HW). The knives are angled 45° for precise bevel cuts and a perfect finish. This cutter head is perfectly suited for cutting 45° bevels, for instance to produce frames. Thanks to the tungsten carbide knives, this cutter head cuts effortlessly through solid boards or solid woods and you always obtain a smooth surface. Also suitable for use on laminated materials.
Available with bore 30mm or 50mm.
Prolongez considérablement la durée de vie de votre plaqueuse de chants portable ou stationnaire. Le Cantspray Virutex est un spray antiadhésif sans silicone. Convient pour traiter toutes les pièces mobiles de votre plaqueuse de chants et empêcher l'accumulation de colle. Il est recommandé d'appliquer le Virutex Cantspray avant et après l'utilisation de votre machine pour un résultat optimal.
Cette fraise à rayon creux permet d'arrondir facilement et rapidement les coins pour obtenir une forme ronde. La fraise peut également être utilisée pour créer une rainure à fond plat entre deux formes rondes. En augmentant la profondeur de travail, vous obtenez le classique "quart de rond" qui est typique pour les bords des tables à manger, par exemple. Grâce à ses tranchants en carbure de haute qualité (widia), cette fraise peut être utilisée sur la plupart des types de bois.
The MT58K table is mobile, height-adjustable (with four fixed positions) and foldable for easy storage. The table provides a stable and solid base for attaching and transporting machines. The table can be moved or adjusted in height while the machine is attached. As a result, you do not have to constantly assemble or disassemble the machine. Adjusting the height is easy. Operate with your foot at the bottom of the height adjustment, then use the lever to secure it in the correct position. The maximum load-bearing capacity of the table is 100kg. Thanks to its small size, this table is ideal for use on location.
Extension pieces are optionally available.
Set profielmessen hoogte 50mm Nr. 2079 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Solid wood Pocket-Hole plugs, standard size. These plugs were specially designed to provide extra strong connections. The Pocket-Hole Jigs ensure that these plugs are concealed seamlessly.
Straight router bits are specifically designed for making grooves in most types of wood or several plastics. These router bits are finished with carbide cutting edges. Thanks to the carbide cutting edges, the router bit delivers high quality results for all your projects and a long working life.
This router bit can be used to work on most wood types or plastics. Thanks to the high quality finish of the bit, it is also possible to make grooves on different plastics such as acrylics (plexiglass), polycarbonate, polypropylene or PVC. To be used in router milling machines or CNC machines.
Showroom model! Unused machine
Compact machine with many possibilities
Large swivel wheels, smooth running in regulation.
2.2KW 3 HP
2 speeds Poly belt 10,000 and 8000 tr/min
Left and right rotating
Operation from above
Includes spindle 30mm, interchangeable spindle 20mm and clamping bushings for router.
Chassis on wheels included
Duro-Polish is ideal for polishing and pre-polishing stainless steel. Thanks to the abrasive's lamellar structure, the felt is not "burned" during the polishing process, preventing streaking. It is important to use DuroPol only in combination with the right polishing paste: pre-polishing paste should be used for pre-polishing, while gloss paste is suitable for high-gloss polishing. This combination allows you to achieve high-quality polishing results without leaving streaks.
Y connector large diameter 100mm and small diameter 60mm to be used with the Air Flux dust extractors.
This pneumatic vacuum table is designed to clamp smooth, non-porous workpieces. The vacuum between the base of the table and the workpiece ensures firm clamping and leaves no traces after use. To make the table vacuum, it must be connected to an external compressor (not included). Thanks to its compact size, this vacuum table is suitable for use in the workshop as well as outdoors. Because you can place the table both vertically and horizontally, this module is ideal for a wide range of applications.
Using the rubber seals included as standard, you can easily divide the table into smaller sections. Standard delivery with one rubber seal already installed and a transparent tube for the air supply with 1/4" quick-release coupling.
This cutter head for profile knives of height up to 40mm can be used on spindle moulding machines with a bore of 30mm. This head is compatible with all profile knives up to height of 40mm.
Filterpatroon met canister filter en restzak voor de Air Flux Dusty AF-950WM. De canister filter vangt stof op tot een grootte van 1 micron, tegenover 30 micron voor de standaardfilterzak en 5 micron voor de verbeterde fibre filterzak. De filter is zelfreinigend dankzij de hendel bovenaan het patroon. Draai eenvoudig aan de hendel om stof van de plooien in de filter te verwijderen, waarna het onderaan in de meegeleverde pvc restzak valt.
Dit filterpatroon kan ook gebruikt worden om uw Air Flux AF-950 te upgraden naar een stofopvang tot 1 micron.
Zaaglint met lengte 3345mm om te gebruiken op de TT400 lintzaagmachine van Tendotools. Dit zaaglint beschikt over 6 TPI (tanden per inch) en heeft een breedte van 6mm. Dit zaaglint in gehard staal "Flexback" is erg geschikt voor multifunctioneel zagen. Gebruik dit zaaglint zowel voor hout als voor plastics. De tanden van het zaagblad kregen een extra thermische behandeling voor verhoogde hardheid. Hierdoor blijft de band erg soepel en verhoogt uw zaagcomfort dankzij de hardheid van de tanden.
Forstner drill bit with cylindrical shank for boring hinges with the best quality on every kind of wood or panels. This high quality hinge boring bit has two Tungsten cutting edges, two Tungsten spurs and a HW center point for boring with the best quality on every kind of wood or panels. Right hand boring only
Set profielmessen hoogte 50mm Nr. 2006 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
This pneumatic vacuum table on tiltable support is designed to clamp smooth, non-porous workpieces. To make the table vacuum, it must be connected to an external compressor (not included). Thanks to its compact size, this vacuum table is suitable for use in the workshop as well as outdoors. The head of the support can tilt 90° so that you can place the workpiece in an ideal position. On top of this, the top plate can be rotated 360°. The support must be secured with clamps (not included).
Using the standard supplied rubber seals, you can easily divide the table into smaller sections. Standard delivery with one rubber seal already installed and a transparent tube for the air supply with 1/4" quick-release coupling.
These patented 8 mm dowels can be used in all applications where wooden dowels are used. The dowels provide a strong permanent connection and are applied without the use of glue or tools, providing enormous ease of use as well as time savings.
Available in boxes of 100, 200 or 500.
Le gabarit pour trous de poche Kreg Pocket-Hole Jig 320 est un ensemble de base complet pour les assemblages à trous de poche. Le gabarit de perçage comporte deux guides de perçage, une entretoise amovible et des butées d'épaisseur de matériau très pratiques. La jauge d'épaisseur du matériau et le foret facile à régler inclus rendent l'installation extrêmement simple, tandis que l'adaptateur de serrage pratique et la base antidérapante maintiennent le gabarit en position précise pendant que vous percez des trous de poche parfaitement positionnés à chaque fois. Le gabarit et les composants inclus sont fournis dans un coffret durable et compact qui offre même de la place pour ranger les vis à trou de poche Kreg. Les guides de perçage sont fabriqués en acier trempé et sont garantis à vie.
This box set gives you an all-in-one solution for making interior cabinets and doors on combi or milling machines. The set consists of a cutter head height 40mm (art.3FR30784030), including four handy profile knives. You will find both a glue cutter and profile/contraprofile knife for making solid connections as well as a V-groove cutter and panel raising profile for the beautiful finishing of your projects. Also in this set is an adjustable grooving cutter (art.3FR3937120300510), including a set of adjusting rings. This grooving cutter with diameter 120mm is adjustable in height between 5mm and 9.5mm, perfect for milling grooves with, among other things, pin and groove joints. Finally, it contains an adaptor for routers. Thanks to this handy piece, which fits exactly on your machine, you can also use your router bits on combi or milling machines.
Set profielmessen hoogte 50mm Nr. 2024 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Extra kogellager om te gebruiken met de bovenfrezen van Sistemi Klein.
Le Kreg Pocket-Hole Jig 720 Pro est le système de connexion professionnel, rapide et efficace avec des accessoires haut de gamme. Avec ce système, vous pouvez réaliser des trous de poche très résistants dans des matériaux d'une épaisseur minimale de 13 mm (1/2") et d'une épaisseur maximale de 38 mm (1 1/2").
Le Kreg 720 Pro est livré avec une station d'accueil. Cette extension offre plus de support pour des équipements plus volumineux et plus d'espace de stockage. Les pièces latérales de la station d'accueil peuvent être facilement pliées pour ranger le système lorsqu'il n'est pas utilisé. De plus, les pièces latérales peuvent également être déconnectées du système afin que vous puissiez créer encore plus de support pour votre pièce.
Vous pouvez mesurer l'épaisseur du matériau à l'aide de la jauge d'épaisseur fournie. Au bas du gabarit Kreg Pocket-Hole Jig 720 se trouve un système de rangement intégré pour la perceuse, les embouts et la jauge d'épaisseur du matériau.
Fraises à rainurer sont spécifiquement conçue pour faire des rainures dans des types de bois différents ou des plastiques. Grâce au face de coupe supplémentaire en bout de fraise (Z=2+1), c'est aussi possible de facilement faire de perçage. Ces fraises sont fournis de faces de coupe en carbide. Grâce à ces faces de coupe en carbide le fraise vous assure un résultat parfait de tous votre projets ét une longue durée de vie.
Ce fraise peut être utiliser avec le plupart de types de bois. Grâce a la qualité extraordinaire il est aussi possible d'utiliser les fraises sur les plastiques comme l'acrylat (Plexiglas), polycarbonate, polypropylène ou de PVC. A utiliser dans des défonceuses ou des machines CNC.
Forstnerboor met cilindrische schacht voor het boren van potscharnieren in de meeste houtsoorten of plaatmaterialen. Deze hoogwaardige potscharnierboor met centerpunt is voorzien van twee widia-snijvlakken en twee widia-voorsnijders om een optimale afwerking van uw boorgat te garanderen. Enkel rechtse draairichting.
Saw blade with 56 teeth
Wolf tooth saw blade for classic machines, suitable for fast cutting of different types of wood, wet wood or brush wood. To be used on yard or construction machinery but mainly suitable for firewood saws. The entire saw blade is finished in high quality Chrome-vanadium steel. Made in Germany, take advantage of the extremely solid German quality. Easy to sharpen yourself.
Fraises à rainurer sont spécifiquement conçue pour faire des rainures dans des types de bois différents ou des plastiques. Grâce au face de coupe supplémentaire en bout de fraise (Z=2+1), c'est aussi possible de facilement faire de perçage.
Ce fraise peut être utiliser avec le plupart de types de bois. Grâce a la qualité extraordinaire il est aussi possible d'utiliser les fraises sur les plastiques comme l'acrylat (Plexiglas), polycarbonate, polypropylène ou de PVC. A utiliser dans des défonceuses ou des machines CNC.
Ce guide de position multifonctionnel remplace facilement tous les autres guides ou moules. Le T multi guide est un outil indispensable pour la fabrication de meubles, d'armoires,... Le guide de perçage de haute précision vous permet d'effectuer correctement tous les perçages à une distance de 32 mm (ou plus). Utilisez ce guide pour : les poignées des portes et des glissières, les trous pour les étagères, les charnières ou les guides de tiroir. En option, vous pouvez également utiliser une rallonge pour percer des trous plus longs d'une distance de 32 mm. Ces extensions sont disponibles séparément par jeu de deux.
Le guide possède un trou central et deux trous de forage réglables en acier trempé. La longueur de base de ce conducteur est de 320 mm. Il peut être étendu jusqu'à 810 mm avec les extensions optionnelles. Livraison standard avec une mèche de Ø5mm.
Quarter-circle concave radius cutter to easily and quickly round corners. Increasing the working depth, you will obtain the classical "quarter-round" typical of dining table edges. Perfect finish of your project on different wood types thanks to the HW tungsten cutting edges.
Equipped with a ball bearing for easier work. When using a bit with a large radius, it is advisable to carry out the machining in several steps.
The Kreg® Pocket-Hole Jig 310 makes woodworking a breeze, whether you are starting your first DIY project or have been working with wood for years. The Pocket-Hole Jig 310 has a simple, easy-to-understand adjustment system, allowing you to work with boards and plywood from 13 to 38 mm thick. With a drill guide made of hardened steel and a convenient material thickness stop.
Filtre supplémentaire Air Flux Dusty AF-1100/45. Facile à remplacer, avec sac filtrant protection disponible séparément. Filtration jusqu'à 5µm.
This drill is used to drill square holes and draw rectangular grooves in softwood and hardwood.
Straight router bits are specifically designed for making grooves in most types of wood or several plastics. These router bits are finished with carbide cutting edges. Thanks to the carbide cutting edges, the router bit delivers high quality results for all your projects and a long working life.
This router bit can be used to work on most wood types or plastics. Thanks to the high quality finish of the bit, it is also possible to make grooves on different plastics such as acrylics (plexiglass), polycarbonate, polypropylene or PVC. To be used in router milling machines or CNC machines.
Works with all machines up to 7.5 KW. Connect several machines so that they can be started up together. Use this simultaneous starter when combining a woodworking machine and dust extractor. The starter motor ensures that your dust extraction system starts up automatically four seconds after you start up your woodworking machine yourself. After stopping your woodworking machine, extraction is also stopped a few seconds later. These extra few seconds of suction ensure that your pipes are always clean.
HD, the accessory for heavy work! For outdoor projects, solid railings and even wall frames. Size 14 coated screws ensure rock-solid connections. You need both the drill and the drill guide to get started.
This spare HD drill is for use on the Kreg Foreman machine and has a drilling diameter of 12 mm.
Ce coffret offre un grand nombre d'outils indispensables dont le professionnel a besoin pour démarrer avec sa machine combinée ou sa fraiseuse. L'ensemble se compose d'un porte outils de 50 mm de hauteur, comprenant trois couteaux profilés pratiques qui vous permettent d'effectuer de nombreuses opérations. Cet ensemble comprend également trois autres porte outils : une fraise à rainurer réglable de 120 mm de diamètre, comprenant un jeu de bagues de réglage, une fraise à feuillurer et tenon de 140 mm de diamètre et une fraise à profil plat-bande de 150 mm de diamètre.
Enfin, l'ensemble comprend également quelques accessoires utiles pour commencer à utiliser les différentes têtes de fraisage. Utilisez le reglet de toupilleur pour toujours régler correctement la profondeur et la hauteur de votre coupe. Le jeu (2) de sauterelles rapides verticales est en acier, équipé d'une poignée en PVC et d'un pied de pression en néoprène souple pour éviter d'endommager votre pièce de travail.
Saw blade with 42 teeth
Saw blade with alternate WZ top bevel teeth, suited for cutting across grain of soft wood, hard wood, aluminium-wood profiles or plastic-wood profiles. No noise saw blades for use on radial arm saws or table saws. Make sure to use the right amount of teeth to achieve optimal results of your project. A low number of teeth is suited for fast-paced and rough sawing.
Tuyau anti-statique longueur 3 mètre diamètre 100 mm. A utiliser en combinaison avec les extracteurs de poussière Air Flux.
Mèche de remplacement carrée Kreg #2 de 152 mm de long. Convient pour une utilisation avec les systèmes d'assemblage Kreg. Jeu de 2 pièces
Porte outils d'une hauteur de 90 mm pour utilisation sur des fraiseuses à broche de 30 mm. Cette tête peut être utilisée avec tous nos couteaux de profil de hauteur 90 mm. Ces hauts profils sont principalement utilisés pour le fraisage des lambris, des corniches ou des profils de toit.
The length of this bit is 150mm
Slot mortising bits with chipbreaker, available with left or right hand rotation. These bits are well suited for drilling holes or grooves in most wood types. The bits have two cutting edges in 18% HSS steel and chip breakers.
Le servante à rouleau réglable supporte de grandes pièces jusqu’à 100 kg. Rouleau à roulement à billes chromé avec une base robuste. La base a quatre points pour niveler le support de rouleau. Il est rapide et facile à changer du rouleau au billes Réglage de la hauteur de 77 cm à 116 cm. Le support à rouleau peut être rapidement plié pour le stockage lorsqu'il n'est pas utilisé.
Set profielmessen hoogte 40mm Nr. 0024 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Deze elektrische vacuümtafel op kantelbare steun is ontworpen om gladde, niet poreuze werkstukken vast te klemmen. Om de tafel vacuüm te maken dient ze aangesloten te zijn op het elektrische vacuümsysteem SVE600 van Virutex (standaard inbegrepen). Dankzij het compacte formaat is deze vacuümtafel zowel geschikt om in het atelier te gebruiken als daarbuiten. De kop van de steun kan 90° kantelen zodat u het werkstuk in een ideale positie kan plaatsen. Daarbovenop is de bovenplaat 360° draaibaar. De steun moet vastgezet worden met klemmen (niet inbegrepen).
Met behulp van de standaard geleverd rubber dichtingen verdeelt u de tafel eenvoudig in kleinere secties. Standaardlevering met één rubber dichting al geïnstalleerd en een transparante tube voor de luchttoevoer met 1/4" snelkoppeling.
The Belmash clamping devices provide increased safety when working with your thicknessing machine. Safely plane beams or boards on any Belmash machine. The pusher ensures that the workpiece is clamped to the work surface. This facilitates the flow of material, giving you a clean and precise finish. These clamping devices are easy to install using the screws and washers. The opening can be adjusted by means of a handle on the top and the spring clip on the side. In this way, a good supply and pressure force is always assured.
This pusher is suitable to be used on the Belmash SDM2500.
Spare knife with adjustable diameter 30mm-45mm for the adjustable hinge boring bit of Sistemi Klein (SKU: KL-R110600R).
Set profielmessen hoogte 40mm Nr. 0017 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Straight router bits are specifically designed for making grooves in most types of wood or several plastics. These router bits are finished with carbide cutting edges. Thanks to the carbide cutting edges, the router bit delivers high quality results for all your projects and a long working life.
This router bit can be used to work on most wood types or plastics. Thanks to the high quality finish of the bit, it is also possible to make grooves on different plastics such as acrylics (plexiglass), polycarbonate, polypropylene or PVC. To be used in router milling machines or CNC machines.
1 HP scoring unit, available as an option with the combination machines TT32K5SL, TT320K5 Massif and TT400K5 Massif.
Jeu de 5 outils incontournables pour le tournage, fabriqués en acier HSS (18 %).
Saw blade with 56 teeth
Wolf tooth saw blade for classic machines, suitable for fast cutting of different types of wood, wet wood or brush wood. To be used on yard or construction machinery but mainly suitable for firewood saws. The entire saw blade is finished in high quality Chrome-vanadium steel. Made in Germany, take advantage of the extremely solid German quality. Easy to sharpen yourself.
Deux mousses EVA de remplacement haute densité pour le PushPRO. Les caoutchoucs sont réversibles, ils peuvent donc être utilisés deux fois.
À utiliser uniquement sur un bâton PushPRO (vendu séparément).
A set of ten high quality spacers with a tolerance of 0.01. The thicknesses vary between 1mm and 40mm with a total height of 130mm for all spacers together. These rings are available with bore 30mm (Ø45mm) or with bore 50mm (Ø70mm).
Verstekmeter van de extra topklasse. Fijn instelbare flip-stop, ingefreesde standaardhoeken, uitschuifbare aanslagverlenging
Als u op zoek bent naar accessoires voor uw zaagtafel of freestafel uit de categorie "compromisloos", dan heeft u die zojuist gevonden!
De ITAMAC Xact 36 hoort qua instelbaarheid, precisie, stabiliteit en afwerking zeker thuis in de "non-plus-ultraklasse". Absoluut ongeëvenaarde verstekmeter!
Set profielmessen hoogte 40mm Nr. 0000 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Lame de scie à 32 dents
Lame de scie avec denture alternée, brise-copeaux et conception anti-kickback. Avec peu de dents pour une coupe grossière et rapide du bois. Equipée de dents en carbure de haute qualité (widia). Convient pour la coupe de bois dur et tendre. Peut également être utilisé pour le sciage de panneaux d'aggloméré ou de bois collé sur une face. Idéal pour les scies de chantier ou les scies circulaires à chevalet. Made in Germany, profitez de la solide qualité allemande.
Cette table à vide électrique est conçue pour serrer des pièces lisses et non poreuses. Le vide entre la base de la table et la pièce à usiner assure un serrage ferme et ne laisse aucune trace après utilisation. Pour que la table soit à vide, elle doit être connectée au système de fixation électrique à vide SVE600 de Virutex (non intégré). Grâce à sa taille compacte, cette table à vide peut être utilisée aussi bien dans l'atelier qu'à l'extérieur. Comme vous pouvez placer la table à la fois verticalement et horizontalement, ce module est idéal pour un large éventail d'applications.
Grâce aux joints en caoutchouc fournis en standard, vous pouvez facilement diviser le tableau en sections plus petites. Livraison standard avec un joint en caoutchouc déjà installé.
GRATIS brandhoutkar ter waarde van € 110,00
Robuuste en volledig stalen wipzaag om snel, eenvoudig én veilig brandhout te verzagen. Deze brandhoutwipzaag is volledig conform de CEN-veiligheidsnormen voor dit type machines. Dankzij de afdekkap kan u tijdens het werken niet in de buurt van het zaagblad komen zodat het risico op ongevallen sterk vermindert. Deze wipzaagmachine is voorzien van een zaagblad in hoogwaardig hardmetaal (widia) met diameter Ø700mm. Dit model is voorzien van een driepuntsophanging en aansluiting voor cardanas. De machine kan zo aangedreven worden door een tractor. Net zoals de andere TT700 modellen is deze zaagmachine voorzien van riemaandrijving. Uiterst geschikt voor het kappen van takken of boomstammen met een maximumdikte van 240mm. Volledig gemonteerd bij levering en klaar voor gebruik.
The BOW Portable Saw Featherboard features an innovative use of high-density EVA Foam/foam combs and clamping system that increases input control, dramatically improves recoil and better protects your wood from damage. This compared to the general plastic feaherboards. EVA is a high density, closed cell material with long life that you don't have with the common plastic featherboards. The springs are also unbreakable and, unlike plastic springs, they can be replaced if damaged.
Mounting material included.
Set profielmessen hoogte 40mm Nr. 0050 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Gabarit robuste et de haute qualité pour le fraisage de joints à queue d'aronde à placer sur un établi. Grâce à son cadre robuste et fermé, la stabilité de ce gabarit est inégalée. Standard équipé d'un gabarit avec un pas de 26 mm. Utilisez ce moule avec un douille de copiage de Ø19mm, inclus en standard avec votre défonceuse Virutex ou vendu séparément. Des peignes avec un pas de 16 mm ou 34 mm sont disponibles en option. Serrer les deux pièces de la joint. Compatible avec les défonceuses Virutex
Si vous utilisez une fraise droite, vous pouvez également utiliser ce moule pour réaliser des assemblages à broches droites. Note : Il n'est pas possible de fraiser les queues d'aronde ou les stylos sans utiliser une bague de copie. Le douille de copiage pour pas de 26 mm et le fraise approprié (fraise à queue d'aronde art. 6040050 ou fraise droit art. 1140060) sont tous deux disponibles séparément.
SHOWROOM MODEL
De TT2010 is een veelzijdige schuurmachine met een schuurband van 2010 x 153 mm, een contourtafel voor rondschuurwerk en een afzuigmond.
Set profielmessen hoogte 40mm Nr. 0008 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
This multifunctional position guide easily replaces all other guides or moulds. The T multi guide is an indispensable tool for making furniture, cabinets,... The high-precision drill guide allows you to carry out all drillings with a distance of 32mm (or more) correctly. Use this guide for: handles on doors and slides, holes for shelves, hinges or drawer guides. As an option, you can also use an extension piece to drill longer driving holes with a distance of 32mm. These extensions are available separately per set of two.
The guide has a central borehole and two adjustable boreholes in hardened steel. The basic length for this guide is 320mm. This can be extended up to 810mm with the optional extensions. Standard delivery with a Ø5mm drill bit.
The length of this bit is 140mm
Slot mortising bits with chipbreaker, available with left or right hand rotation. These bits are well suited for drilling holes or grooves in most wood types. The bits have two cutting edges in 18% HSS steel and chip breakers.
Capot en PVC noir avec tube à diamètre 100mm à utiliser avec les systèmes d'aspiration Air Flux. La taille de l’ouverture du capot anti-poussière est de 415x325mm.
Template to be used on the Virutex FR129VB Router for door hinges to mill Argenta Invisible Large. This template is only suitable for the model Invisible Large van Argenta. Other models available. Hinge not included.
Pièce de réduction à 4 pièces jusqu'à 100mm à utiliser avec les modèles differents des aspirateurs Air Flux.
Modèle de salle d'expo
Les scies à table HW110E de Steel City ont déjà prouvé qu'elles étaient l'une des tables de scie de la plus haute qualité dans le monde entier, avec plus de 30 000 clients satisfaits. Les scies à table se caractérisent par une conception et une ingénierie de pointe, un châssis robuste et un système d'entraînement puissant. Apparence et finition rayonnantes, précision et stabilité exceptionnelles, fonctionnement souple et fonctionnalités conviviales. Cette série comprend une table de sciage classique 3PK inclinable à gauche avec un système avancé de changement de coin de fendage ou une table de sciage à logement en queue d'aronde 5,5PK à usage intensif pour les coupes industrielles. Tous ces modèles sont équipés pour être utilisés avec le système Dado (lames de scie à rainures réglables pour couper les rainure et entre autres).
Transformez n'importe quelle perceuse en perceuse à 90° avec le tournevis pour trous de poche à 90° de Kreg. Avec cet accessoire compact pour perceuse, vous pouvez serrer des vis dans des endroits où vous ne pouvez pas les atteindre avec votre perceuse.
La mèche carrée de 7,62 cm fournie est dotée d'une pointe magnétique qui s'enclenche dans la tête d'une vis à trou de poche. Cet accessoire est d'application universelle, c'est-à-dire qu'il convient à toutes les perceuses et à tous les embouts hexagonaux. Grâce à sa conception ergonomique, vous pouvez facilement tenir le tourne-pièce 90° Kreg d'une main tout en utilisant la perceuse de l'autre. Il peut également être utilisé avec une perceuse à percussion. Lorsque vous devez serrer des vis dans des espaces restreints, vous pouvez compter sur le tourneur de trous de poche à 90° de Kreg pour faire le travail.
Deze boortafel van Belmash is compatibel met de SDM2500 machine. De boortafel kan worden geïnstalleerd in plaats van de freestafel. De boortafel kan volledig in hoogte en links/rechts geregeld worden. Inclusief twee klemmen die zorgen voor fixatie van het werkstuk.
De hoekmeter 'Angle Copy' van Virutex zorgt altijd voor de juiste hoek zonder hoeken te moeten bereken of uitmeten. Druk eenvoudig de Angle Copy in de hoek waarin u werkt en het toestel kopieert deze. Met behulp van een knop kan u de gekiopeerde hoek vastzetten zodat steeds de correcte hoek verzaagt. Zowel te gebruiken in binnen- als buitenhoeken. Dankzij de gradenboog kan u de Angle Copy ook gebruiken om handmatig hoeken aan te duiden op uw werkstuk.
The Kreg Pocket-Hole Jig 520 Pro is a practical and versatile jointing system. This system allows you to create very solid pocket holes in materials with a minimum thickness of 13 mm and a maximum thickness of 38 mm.
The Pocket-Hole Jig 520 Pro has a number of unique points. For example, the jig has a 360° rotatable handle. This handle ensures that you can comfortably use the system on any project. In addition, the Pocket-Hole Jig 520 Pro has a built-in clamping system. You simply squeeze the handle until the material is clamped firmly enough. The non-slip material on the 520 Pro ensures that the jointing system will not shift, no matter what position you use the jig in. You can measure the thickness of the material with the supplied material thickness gauge.
Cette fraise à rayon creux permet d'arrondir facilement et rapidement les coins pour obtenir une forme ronde. La fraise peut également être utilisée pour créer une rainure à fond plat entre deux formes rondes. En augmentant la profondeur de travail, vous obtenez le classique "quart de rond" qui est typique pour les bords des tables à manger, par exemple. Grâce à ses tranchants en carbure de haute qualité (widia), cette fraise peut être utilisée sur la plupart des types de bois.
Content
Deze transporthendel is standaard voorzien van een klem waardoor deze hendel geschikt is voor meerdere functies. Inzetbaar als kantenpers, hoekpers of transporthendel. Dankzij het ontwerp in aluminium is deze hendel erg sterk en robuust. De maximale last bedraagt 70kg. Als kantenpers kan u de PC81U zowel gebruiken op rechte panelen, als op holle of bolle panelen. Als hoekpers wordt deze hendel dan weer de ideale tool om bijvoorbeeld kaders te maken. De klem is afneembaar en door de handgreep van positie te veranderen is de PC81U eenvoudig om te bouwen tot transporthendel. Geschikt voor panelen van dikte tussen 0mm en 46mm.
Voor het verbinden van panelen van 16 of 19mm dikte met behulp van deuvels (Ø8mm) of schroeven. Werk met een hoge precisie & hoogkwalitatieve afwerking, zonder de nood om achteraf bij te stellen. Deze positiegeleider is zowel geschikt om gaten te boren op de kopse kant, langsheen de zijkant, of op elke positie in het midden van het paneel. Maximumbreedte van het paneel om de geleider te plaatsen is 630mm. Standaardlevering met inzetstukken voor planken van 16 mm, verloopringen en boorstop.
Round-over router bit to easily and quickly round corners. Increasing the working depth, you will obtain the classical "quarter-round" typical of dining table edges. Perfect finish of your project on different wood types thanks to the HW tungsten cutting edges.
Equipped with a ball bearing for easier work. When using a bit with a large radius, it is advisable to carry out the machining in several steps.
Kreg assortment case with the six most commonly used screws. There are 30 or 50 of each screw in an assortment case.
The case contains four lengths of screws for softwood and one length for hardwood. The fifth screw is blue and has a triple coating, making it corrosion resistant. It can therefore be used both outdoors and indoors in damp rooms.
Contents:
- 50x SPS-C1 1" (25 mm)
- 50x SML-F125 1 1/4" (32 mm)
- 50x SML-C125 1 1/4" (32 mm)
- 50x SML-C150 1 1/2" (38 mm)
- 30x SML-C250 2 1/2" (64 mm)
- 30x SML-C250B 2 1/2" (64 mm)
Quarter-circle concave radius cutter to easily and quickly round corners. Increasing the working depth, you will obtain the classical "quarter-round" typical of dining table edges. Perfect finish of your project on different wood types thanks to the HW tungsten cutting edges.
Equipped with a ball bearing for easier work. The smaller bearing provides an upright standing side to the rounding. When using a bit with a large radius, it is advisable to carry out the machining in several steps.
Tweemaal uitgang Ø125mm voor gebruik met de Air Flux Cyclone stofafzuigingen. De grote diameter is 203mm, rechtstreeks aansluitbaar op de cycloon afzuiggroepen, met vertakkingen naar 2x125mm.
Replacement waste bags PVC 120µm to be used with the Air Flux dust extractors. These bags are compatible with the Air Flux Dusty 1020AF.
Specially designed hand gluer for gluing large surfaces with vinyl (white) adhesives. Available in two models with different roll widths and glue container capacities. Model EM25D is equipped with a roll with a width of 122mm and a capacity of 1kg. The larger model EM125T has a roll with a width of 180mm and a capacity of 1.4kg. The machine is equipped with a trigger on the handle for easy opening and closing of the glue container. Simply press the trigger to run the glue over the roll. Using this trigger you will always obtain the right amount of glue for your project. Thanks to the support, the hand gluer can easily be put away. For cleaning, you can keep this adhesive under water without risk of damage. At the top there is a second roller (width 92mm) for stationary glueing along the top with the machine.
Attention: this adhesive comes standard with a rubber roller, suitable for vinyl adhesives and water-based adhesives. For synthetic adhesives an optional PU roll is available (Ref. 2504065). This hand gluer is also available without roller at the top (models EM26D and EM126T).
Square carbide plaque for roughing gouge 11 mm
Set profielmessen hoogte 40mm Nr. 0046 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Groefzaagblad met vlakke (FZ), widia zaagtanden om groeven te trekken in hardhout, zacht hout, gelamineerde panelen en andere producten op basis van hout. De zaagbladen hebben een asgat van 30mm en zijn ideaal voor gebruik op freesmachines of op zaagtafels.
Dit zaagblad is beschikbaar in verschillende diameters
Set profielmessen hoogte 50mm Nr. 2004 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Saw blade with 36 teeth
Saw blade with alternate top bevel teeth, chip breakers and anti-kickback design. With few teeth for a rough and fast cut of the wood. Equipped with teeth in high quality carbide (widia). Suitable for both shortening and longitudinal cutting of hard and soft types of wood. Can also be used for sawing chipboard or single-sided laminated wood. Ideal for construction site saws or tilting log saws. Made in Germany, take advantage of the extremely solid German quality.
Set profielmessen hoogte 40mm Nr. 0007 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Set profielmessen hoogte 40mm Nr. 0048 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Set of profile knives of height 40mm Nr. 0087 suited for universal moulding blocks. Used for moulding of wood at low costs. The steel alloy with 16% cobalt guarantees a high quality cut and a comfortable cutting process.
Deze frees is geschikt voor het maken van zwaluwstaartverbindingen. Zwaluwstaartverbindingen zijn klassieke, maar ijzersterke mechanische verbindingen om te gebruiken in houtbewerking. Gebruik deze verbindingen om kasten, lades, kisten of andere hoekverbindingen te vervaardigen. Dankzij de hardmetalen (widia) snijvlakken is een precieze en nette afwerking van uw freeswerken te allen tijde gegarandeerd.
Om sneller en efficiënter te werken kan u gebruik maken van een mal voor zwaluwstaartverbindingen.
Reducer diameter 100-50mm to be used with the Air Flux dust extractors.
Verlengstukken voor de wielkit WK600. Gebruik de twee staven (lengte: 915mm) om de originele uit uw wielkit te vervangen. Vervoer grotere machines zonder verlies van draagkracht.
Krachtige, robuuste vlak- en vandiktebank met inductiemotor, geschikt voor elke werkplaats. Deze machine is verkrijgbaar met een motor op 230V of drie fasen 400V. Dankzij het stevige, stalen design met gietijzeren werkbladen is deze machine bestand tegen zwaar dagelijks gebruik. De werktafels zijn onderaan voorzien van een zwaar profiel om de vlakheid te allen tijde te behouden. De tafels scharnieren onafhankelijk van elkaar en kunnen omhoog geplaatst worden. Op deze manier kan u maximaal gebruik maken van de capaciteiten van de vandiktebank.
Deze vandiktebank is eenvoudig instelbaar met behulp van een soepel draaiend, traploos draaiwiel. Voorzien van een millimeter indeling zodat u eenvoudig de correcte hoogte kan aflezen. Tijdens het werken blijft de vandikte unit probleemloos in positie staan met behulp van de vergrendeling. In combinatie met de toevoersnelheid van 6m/min zorgt dit voor een erg gladde, egale afwerking van al uw werkstukken.
Om erg precies te kunnen schaven is deze machine bovenaan voorzien van een stevige, aluminium geleider. Deze geleider kan ingesteld worden onder hoek met twee stops voor 90° en 45°. Met behulp van de zware schaafas, voorzien van drie schaafbeitels, is een goede afwerking steeds gegarandeerd. Het afvoeren van de spaanders gebeurt via een scharnierende kap. Deze kap kan aangesloten worden op een stofafzuiging met behulp van de uitlaat met Ø100mm. Standaard is deze machine voorzien van schaafbeitels met een dikte van 1,5mm. Dikkere schaafbeitels (3mm) zijn verkrijgbaar op aanvraag.
Fraises à rainurer sont spécifiquement conçue pour faire des rainures dans des types de bois différents ou des plastiques. Grâce au face de coupe supplémentaire en bout de fraise (Z=2+1), c'est aussi possible de facilement faire de perçage. Le fraise est réalisé complètement en métal dure (carbide) et a une finition spéciale 'micrograin' pour des prestations améliorés. Grâce à tous ces qualités, le fraise vous assure un résultat parfait de tous votre projets ét une longue durée de vie.
Ce fraise peut être utiliser avec le plupart de types de bois. Grâce a la qualité extraordinaire il est aussi possible d'utiliser les fraises sur les plastiques comme l'acrylat (Plexiglas), polycarbonate, polypropylène ou de PVC. A utiliser dans des défonceuses ou des machines CNC.
Straight router bits are specifically designed for making grooves in most types of wood or several plastics. These router bits are finished with carbide cutting edges. Thanks to the carbide cutting edges, the router bit delivers high quality results for all your projects and a long working life.
This router bit can be used to work on most wood types or plastics. Thanks to the high quality finish of the bit, it is also possible to make grooves on different plastics such as acrylics (plexiglass), polycarbonate, polypropylene or PVC. To be used in router milling machines or CNC machines.
Klein® trimming bits with straight cut are suitable for smooth and well-finished edges on melamine and veneered panels. The ball bearing, having the same diameter of the cutters, trims any overlap leaving a flat and smooth edge. Two flutes provide fast cutting and good chipping ejection.
Set profielmessen hoogte 40mm Nr. 0037 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Works with all machines up to 7.5 KW. Connect several machines so that they can be started up together. Use this simultaneous starter when combining a woodworking machine and dust extractor. The starter motor ensures that your dust extraction system starts up automatically four seconds after you start up your woodworking machine yourself. After stopping your woodworking machine, extraction is also stopped a few seconds later. These extra few seconds of suction ensure that your pipes are always clean.
Straight router bits are specifically designed for making grooves in most types of wood or several plastics. Together with two straight cutting edges, there is a special tip on the bottom (Z=2+1) which allows easy and precise boring. The router bit is solid carbide, with special micrograin finishing for best performance. Thanks to these combined qualities the router bit delivers high quality results for all your projects and a long working life. This router bit can be used to work on most wood types or plastics. Thanks to the high quality finish of the bit, it is also possible to make grooves on different plastics such as acrylics (plexiglass), polycarbonate, polypropylene or PVC. To be used in router milling machines or CNC machines.
De Itamac Eagle series zijn hoogwaardige freesmachines, specifiek ontwikkeld voor professionele freestoepassingen. Ontworpen met het oog op zowel functionaliteit als comfort, beschikt deze machine over alle mogelijke functies voor een freesmachine uit deze klasse. Voorzien van een extra zwaar chassis, een massief gietijzeren beschermkap met aluminium geleiders en fijnregeling. De krachtige 230V of 400V motor levert 3PK en zorgt ervoor dat deze tafel bijna elke freesopdracht aankan. De Itamac Eagle HW300E heeft een as van 30mm. Mits de optioneel verkrijgbare frees as en spantangen kan de machine ook ingezet worden om te profileren met behulp van bovenfrezen. De grote gietijzeren tafel garandeert de nodige stabiliteit tijdens het werken. Inzetbaar op vier snelheden, met gecentraliseerd controlepaneel boven de machine.
Fraises à rainurer sont spécifiquement conçue pour faire des rainures dans des types de bois différents ou des plastiques. Grâce au face de coupe supplémentaire en bout de fraise (Z=2+1), c'est aussi possible de facilement faire de perçage. Ces fraises sont fournis de faces de coupe en carbide. Grâce à ces faces de coupe en carbide le fraise vous assure un résultat parfait de tous votre projets ét une longue durée de vie.
Ce fraise peut être utiliser avec le plupart de types de bois. Grâce a la qualité extraordinaire il est aussi possible d'utiliser les fraises sur les plastiques comme l'acrylat (Plexiglas), polycarbonate, polypropylène ou de PVC. A utiliser dans des défonceuses ou des machines CNC.
Bandsaw blade with length 3607mm for use on the TT500X band saw machine from Tendotools. This saw blade has 4 TPI (teeth per inch) and has a width of 13, 16 or 20mm. This bandsaw blade in tempered steel "Flexback" is very suitable for multipurpose sawing. Use this saw ribbon for both wood and plastics. The teeth of the saw blade were given an additional heat treatment for increased hardness. This keeps the band very supple and increases your cutting comfort thanks to the hardness of the teeth.
Light and powerful sander for sanding all types of surfaces. The ergonomic design ensures a perfect grip and comfortable working. Thanks to the perfect balancing, you can enjoy a reduced vibration level. Equipped with a large polyurethane sanding base (93x185mm). Because of these dimensions, the sanding base prevents the metal parts from damaging corners or edges during accurate work. On the other hand, the sanding surface is still perfectly suitable for sanding narrow surfaces, e.g. between mouldings. Equipped with an integrated dust extractor and dust bag.
Optionally, a base plate with Velcro is available.
Set profielmessen hoogte 40mm Nr. 0057 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
The thicknessing unit is an indispensable tool for thickness planing on the Belmash SDM2500 and makes it possible to obtain a workpiece of excellent quality. It has its own cutterblock that is driven via the motor of the SDM2500. With this unit you can plan thickness on the SDM2500 of 5-103mm and a planing width of 250mm.
Set profielmessen hoogte 40mm Nr. 0071 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Set profielmessen hoogte 40mm Nr. 0069 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Schuurband voor schuurmachine TT915.
915 x 100 mm
Verkrijgbaar in korrel 40 - 60 - 80 - 100 - 120 - 150
Deze schuurband kan gebruikt worden voor het ontbramen en schuren van staal, aluminium, non-ferromaterialen, hout en kunststof.
Adapter ring to reduce the bore of your saw blade to comply with your machine. Make sure every saw blade is compatible with your own machine thanks to these convenient reduction rings.
Reduction from bore 20mm to 12,7mm.
This chisel allows you to make sharp narrows and hollow out rounded surfaces straight. Is ideally suited for sizing diameters when turning between centers.
Cette base mobile de Belmash est compatible avec les machines Universal 2000, SDM2500, SDMR2500 et SDR2200. Placez votre machine Belmash à une hauteur idéale et rendre mobile.
Vane d'arrêt murale, diamètre 100 mm, à utiliser en combinaison avec les systèmes d'extraction de poussière Air Flux.
Pistolet à air chaud avec contrôle électronique de la température et deux réglages de chaleur. Cela vous permet de toujours adapter l'outil au travail que vous faites. Ce pistolet thermique est très adapté pour former ou souder des plastiques, travailler avec des autocollants/films, rétracter des fils de fer et bien plus encore. Livraison standard avec une buse. De plus, ce pistolet thermique est compatible avec la plupart des accessoires actuellement disponibles sur le marché.
Set profielmessen hoogte 50mm Nr. 2009 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Set profielmessen hoogte 50mm Nr. 2005 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Antistatische afzuigslang lengte 6 meter diameter 100 mm. Te gebruiken in combinatie met de stofafzuigingen van Air Flux.
Cutter head in light alloy with reversible blades in high quality tungsten carbide (HW). The knives are angled 45° for precise bevel cuts and a perfect finish. This cutter head is perfectly suited for cutting 45° bevels, for instance to produce frames. Thanks to the tungsten carbide knives, this cutter head cuts effortlessly through solid boards or solid woods and you always obtain a smooth surface. Also suitable for use on laminated materials.
Available with bore 30mm or 50mm.
Prolongez considérablement la durée de vie de votre plaqueuse de chants portable ou stationnaire. Le Cantspray Virutex est un spray antiadhésif sans silicone. Convient pour traiter toutes les pièces mobiles de votre plaqueuse de chants et empêcher l'accumulation de colle. Il est recommandé d'appliquer le Virutex Cantspray avant et après l'utilisation de votre machine pour un résultat optimal.
Cette fraise à rayon creux permet d'arrondir facilement et rapidement les coins pour obtenir une forme ronde. La fraise peut également être utilisée pour créer une rainure à fond plat entre deux formes rondes. En augmentant la profondeur de travail, vous obtenez le classique "quart de rond" qui est typique pour les bords des tables à manger, par exemple. Grâce à ses tranchants en carbure de haute qualité (widia), cette fraise peut être utilisée sur la plupart des types de bois.
The MT58K table is mobile, height-adjustable (with four fixed positions) and foldable for easy storage. The table provides a stable and solid base for attaching and transporting machines. The table can be moved or adjusted in height while the machine is attached. As a result, you do not have to constantly assemble or disassemble the machine. Adjusting the height is easy. Operate with your foot at the bottom of the height adjustment, then use the lever to secure it in the correct position. The maximum load-bearing capacity of the table is 100kg. Thanks to its small size, this table is ideal for use on location.
Set profielmessen hoogte 50mm Nr. 2079 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Solid wood Pocket-Hole plugs, standard size. These plugs were specially designed to provide extra strong connections. The Pocket-Hole Jigs ensure that these plugs are concealed seamlessly.
Straight router bits are specifically designed for making grooves in most types of wood or several plastics. These router bits are finished with carbide cutting edges. Thanks to the carbide cutting edges, the router bit delivers high quality results for all your projects and a long working life.
This router bit can be used to work on most wood types or plastics. Thanks to the high quality finish of the bit, it is also possible to make grooves on different plastics such as acrylics (plexiglass), polycarbonate, polypropylene or PVC. To be used in router milling machines or CNC machines.
Compact machine with many possibilities
Large swivel wheels, smooth running in regulation.
2.2KW 3 HP
2 speeds Poly belt 10,000 and 8000 tr/min
Left and right rotating
Operation from above
Includes spindle 30mm, interchangeable spindle 20mm and clamping bushings for router.
Chassis on wheels included
Polishing brush for polishing stainless steel, metal, lacquer, etc. Slat structure prevents the felt from burning. This brush allows you to achieve high-quality polishing results without leaving streaks.
Y connector large diameter 100mm and small diameter 60mm to be used with the Air Flux dust extractors.
This pneumatic vacuum table is designed to clamp smooth, non-porous workpieces. The vacuum between the base of the table and the workpiece ensures firm clamping and leaves no traces after use. To make the table vacuum, it must be connected to an external compressor (not included). Thanks to its compact size, this vacuum table is suitable for use in the workshop as well as outdoors. The table itself must be fixed with screws in the provided holes. Because you can place the table both vertically and horizontally, this module is ideal for a wide range of applications. Clamp workpieces for gluing, milling, trimming, etc...
Using the standard supplied rubber seals, you can easily divide the table into smaller sections. This is very useful for securing small pieces, for example. To secure larger workpieces, you can use multiple modules to prevent sagging. The optional distributor (ref. 5046350) allows you to connect up to five basic pneumatic modules at the same time. In this way you can operate them synchronously. Standard delivery with one rubber seal already installed and a transparent tube for the air supply with 1/4" quick-release coupling.
This cutter head for profile knives of height up to 40mm can be used on spindle moulding machines with a bore of 30mm. This head is compatible with all profile knives up to height of 40mm.
Filterpatroon met canister filter en restzak voor de Air Flux Dusty AF-950WM. De canister filter vangt stof op tot een grootte van 1 micron, tegenover 30 micron voor de standaardfilterzak en 5 micron voor de verbeterde fibre filterzak. De filter is zelfreinigend dankzij de hendel bovenaan het patroon. Draai eenvoudig aan de hendel om stof van de plooien in de filter te verwijderen, waarna het onderaan in de meegeleverde pvc restzak valt.
Dit filterpatroon kan ook gebruikt worden om uw Air Flux AF-950 te upgraden naar een stofopvang tot 1 micron.
Zaaglint met lengte 3345mm om te gebruiken op de TT400 lintzaagmachine van Tendotools. Dit zaaglint beschikt over 6 TPI (tanden per inch) en heeft een breedte van 6mm. Dit zaaglint in gehard staal "Flexback" is erg geschikt voor multifunctioneel zagen. Gebruik dit zaaglint zowel voor hout als voor plastics. De tanden van het zaagblad kregen een extra thermische behandeling voor verhoogde hardheid. Hierdoor blijft de band erg soepel en verhoogt uw zaagcomfort dankzij de hardheid van de tanden.
Forstner drill bit with cylindrical shank for boring hinges with the best quality on every kind of wood or panels. This high quality hinge boring bit has two Tungsten cutting edges, two Tungsten spurs and a HW center point for boring with the best quality on every kind of wood or panels. Right hand boring only
Set profielmessen hoogte 50mm Nr. 2006 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
This pneumatic vacuum table on tiltable support is designed to clamp smooth, non-porous workpieces. The vacuum between the base of the table and the workpiece ensures firm clamping and leaves no traces after use. To make the table vacuum, it must be connected to an external compressor (not included). Thanks to its compact size, this vacuum table is suitable for use in the workshop as well as outdoors. The head of the support can tilt 90° so that you can place the workpiece in an ideal position. On top of this, the top plate can be rotated 360°. The support must be secured with clamps (not included). Because you can place the table both vertically and horizontally, this module is ideal for a wide range of applications. Clamp workpieces for gluing, milling, trimming, etc...
Using the standard supplied rubber seals, you can easily divide the table into smaller sections. This is very useful for securing small pieces, for example. To secure larger workpieces, the optional SVN470 auxiliary support is available. This support is specifically designed to connect to the SVN450 or SVN460 model. Using a distribution block, you can connect up to 4 supports at the same time. In this way you can operate them synchronously. Standard delivery with one rubber seal already installed and a transparent tube for the air supply with 1/4" quick-release coupling.
Le gabarit pour trous de poche Kreg Pocket-Hole Jig 320 est un ensemble de base complet pour les assemblages à trous de poche. Le Kreg Pocket-Hole Jig 320 facilite plus que jamais la réalisation de projets en bois, que ce soit votre premier projet de bricolage ou que vous travailliez le bois depuis des années. Le Pocket-Hole Jig 320 utilise un processus d'installation simple et facile à comprendre qui vous donne la polyvalence dont vous avez besoin pour construire avec des planches et du contreplaqué de toute épaisseur comprise entre +/- 12 mm et +/- 38 mm.
Le 320 est doté de deux guides de perçage, d'une entretoise amovible et de butées d'épaisseur de matériau pratiques. La jauge d'épaisseur du matériau et le foret facile à régler inclus rendent l'installation extrêmement simple, tandis que l'adaptateur de serrage pratique et la base antidérapante maintiennent le gabarit en position précise pendant que vous percez des trous de poche parfaitement positionnés à chaque fois. Le gabarit et les composants inclus sont fournis dans un coffret durable et compact qui offre même de la place pour ranger les vis à trou de poche Kreg. Les guides de perçage sont fabriqués en acier trempé et sont garantis à vie.
Quelques améliorations supplémentaires:
Conception Twist-Apart - les guides de perçage et l'entretoise se tordent et se verrouillent pour déterminer facilement l'espacement des trous.
Foret EasySet - les repères gravés sur le foret et la butée de profondeur avec fenêtre de visualisation simplifient la configuration du foret.
Adaptateur de serrage - fixation pratique pour un serrage facile et rapide des pinces Kreg et d'autres marques.
Jauge d'épaisseur du matériau/clé Allen - aide à définir la profondeur correcte du foret, fonctionne également comme une clé Allen.
Le gabarit Pocket-Hole Jig 320 est fourni avec deux gabarits de perçage, une entretoise, un foret à échelons avec butée de perçage, un adaptateur de serrage, une jauge d'épaisseur de matériau, un embout de vis, un jeu de vis Kreg 32 mm, un jeu de vis Kreg Blue Kote 64 mm et un manuel. Tout est livré ensemble dans un coffret.
This box set gives you an all-in-one solution for making interior cabinets and doors on combi or milling machines. The set consists of a cutter head height 40mm (art.3FR30784030), including four handy profile knives. You will find both a glue cutter and profile/contraprofile knife for making solid connections as well as a V-groove cutter and panel raising profile for the beautiful finishing of your projects. Also in this set is an adjustable grooving cutter (art.3FR3937120300510), including a set of adjusting rings. This grooving cutter with diameter 120mm is adjustable in height between 5mm and 9.5mm, perfect for milling grooves with, among other things, pin and groove joints. Finally, it contains an adaptor for routers. Thanks to this handy piece, which fits exactly on your machine, you can also use your router bits on combi or milling machines.
Set profielmessen hoogte 50mm Nr. 2024 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Extra kogellager om te gebruiken met de bovenfrezen van Sistemi Klein.
Le Kreg Pocket-Hole Jig 720 Pro est le système de connexion professionnel, rapide et efficace avec des accessoires haut de gamme. Avec ce système, vous pouvez réaliser des trous de poche très résistants dans des matériaux d'une épaisseur minimale de 13 mm (1/2") et d'une épaisseur maximale de 38 mm (1 1/2").
Le Kreg 720 Pro est livré avec une station d'accueil. Cette extension offre plus de support pour des équipements plus volumineux et plus d'espace de stockage. Les pièces latérales de la station d'accueil peuvent être facilement pliées pour ranger le système lorsqu'il n'est pas utilisé. De plus, les pièces latérales peuvent également être déconnectées du système afin que vous puissiez créer encore plus de support pour votre pièce.
Avec la butée de matériau fournie, vous facilitez encore plus les travaux répétitifs. Vous glissez simplement la butée sur la pièce latérale de la station d'accueil et cela crée une stabilité supplémentaire pour votre pièce. Le bouchon de matériau peut être stocké dans la station d'accueil après utilisation.
La pince pour Pocket-Hole Jig en acier incluse est idéale pour fixer votre système de connexion à votre surface de travail. Cela en fait un système de connexion complet et professionnel pour votre établi. La pince est également facile à ranger dans la station d'accueil après utilisation.
La configuration du Kreg Jig 720 Pro est simple et rapide. Il vous suffit de placer votre matériau dans le gabarit et de pousser le levier vers le bas. Le système fait alors tout le travail pour vous et s'ajuste à la bonne épaisseur. Le levier vous donne également le contrôle complet de la force de serrage ! De plus, le système est doté d'un matériau antidérapant. Cela maintiendra votre pièce solidement en place sans marquer votre bois.
Vous pouvez mesurer l'épaisseur du matériau à l'aide de la jauge d'épaisseur fournie. Les dimensions suivantes y sont indiquées : 1/2”, 3/4” et 1 1/2” (13, 19 et 38 mm). Ces mesures correspondent aux mesures sur le foret étagé. Vous serrez la butée de perçage à la bonne taille avec la jauge d'épaisseur de matériau qui est également une clé Allen.
Au bas du Kreg 720 Pro se trouve un système de stockage intégré pour la perceuse, les embouts de vis et la jauge d'épaisseur de matériau. A côté de l'espace de stockage, les dimensions sont indiquées, avec plusieurs étapes intermédiaires. Cela vous permet d'ajuster la butée de perçage encore plus précisément sur le foret.
Le système de connexion Kreg 720 Pro est également livré avec une pièce d'extraction qui peut être fixée à gauche et à droite du gabarit de perçage. Un tuyau d'extraction peut alors être connecté à celui-ci. De cette façon, la poussière et les copeaux de bois sont aspirés et vous continuez à avoir une bonne vue sur votre surface de travail. Cela rend les trous de poche beaucoup plus efficaces.
Le système de connexion Kreg peut être utilisé horizontalement et verticalement. De cette façon, vous pouvez faire des trous de poche comme vous le souhaitez.
Comme vous en avez l'habitude chez Kreg, ce système est également basé sur la durabilité. Grâce à la construction en plastique résistant aux chocs et durable avec un noyau en acier trempé, vous pouvez être assuré que le système durera.
Le 720 Pro est livré avec 160 vis Pocket-Hole dans les deux tailles les plus populaires. Vous recevrez également un plan de projet. Vous pouvez donc commencer tout de suite!
Fraises à rainurer sont spécifiquement conçue pour faire des rainures dans des types de bois différents ou des plastiques. Grâce au face de coupe supplémentaire en bout de fraise (Z=2+1), c'est aussi possible de facilement faire de perçage. Ces fraises sont fournis de faces de coupe en carbide. Grâce à ces faces de coupe en carbide le fraise vous assure un résultat parfait de tous votre projets ét une longue durée de vie.
Ce fraise peut être utiliser avec le plupart de types de bois. Grâce a la qualité extraordinaire il est aussi possible d'utiliser les fraises sur les plastiques comme l'acrylat (Plexiglas), polycarbonate, polypropylène ou de PVC. A utiliser dans des défonceuses ou des machines CNC.
Forstnerboor met cilindrische schacht voor het boren van potscharnieren in de meeste houtsoorten of plaatmaterialen. Deze hoogwaardige potscharnierboor met centerpunt is voorzien van twee widia-snijvlakken en twee widia-voorsnijders om een optimale afwerking van uw boorgat te garanderen. Enkel rechtse draairichting.
Saw blade with 56 teeth
Wolf tooth saw blade for classic machines, suitable for fast cutting of different types of wood, wet wood or brush wood. To be used on yard or construction machinery but mainly suitable for firewood saws. The entire saw blade is finished in high quality Chrome-vanadium steel. Made in Germany, take advantage of the extremely solid German quality. Easy to sharpen yourself.
Fraises à rainurer sont spécifiquement conçue pour faire des rainures dans des types de bois différents ou des plastiques. Grâce au face de coupe supplémentaire en bout de fraise (Z=2+1), c'est aussi possible de facilement faire de perçage. Le fraise est réalisé complètement en métal dure (carbide) et a une finition spéciale 'micrograin' pour des prestations améliorés. Grâce à tous ces qualités, le fraise vous assure un résultat parfait de tous votre projets ét une longue durée de vie.
Ce fraise peut être utiliser avec le plupart de types de bois. Grâce a la qualité extraordinaire il est aussi possible d'utiliser les fraises sur les plastiques comme l'acrylat (Plexiglas), polycarbonate, polypropylène ou de PVC. A utiliser dans des défonceuses ou des machines CNC.
Ce guide de position multifonctionnel remplace facilement tous les autres guides ou moules. Le T multi guide est un outil indispensable pour la fabrication de meubles, d'armoires,... Le guide de perçage de haute précision vous permet d'effectuer correctement tous les perçages à une distance de 32 mm (ou plus). Utilisez ce guide pour : les poignées des portes et des glissières, les trous pour les étagères, les charnières ou les guides de tiroir. En option, vous pouvez également utiliser une rallonge pour percer des trous plus longs d'une distance de 32 mm. Ces extensions sont disponibles séparément par jeu de deux.
Le guide possède un trou central et deux trous de forage réglables en acier trempé. La longueur de base de ce conducteur est de 320 mm. Il peut être étendu jusqu'à 810 mm avec les extensions optionnelles. Livraison standard avec une mèche de Ø5mm.
Round-over router bit to easily and quickly round corners. Increasing the working depth, you will obtain the classical "quarter-round" typical of dining table edges. Perfect finish of your project on different wood types thanks to the HW tungsten cutting edges.
Equipped with a ball bearing for easier work. When using a bit with a large radius, it is advisable to carry out the machining in several steps.
The Kreg® Pocket-Hole Jig 310 makes woodworking a breeze, whether you are starting your first DIY project or have been working with wood for years. The Pocket-Hole Jig 310 has a simple, easy-to-understand adjustment system, allowing you to work with boards and plywood from 13 to 38 mm thick. With a drill guide made of hardened steel and a convenient material thickness stop.
The included material thickness gauge and Easyset drill bit make setting up the jig a snap, and the GripMaxx™ anti-slip foot holds the jig firmly in place, allowing you to drill perfectly placed pocket holes time after time. With its durable construction and lifetime warranty on the drill guide, the Kreg® Pocket-Hole Jig 310 is guaranteed to give you years of enjoyment. Exactly as you would expect from Kreg®, the leading brand for pocket hole tools.
Filtre supplémentaire Air Flux Dusty AF-1100/45. Facile à remplacer, avec sac filtrant protection disponible séparément. Filtration jusqu'à 5µm.
To drill square holes and draw rectangular grooves in softwood and hardwood. Used on hollow chisel mortisers
Straight router bits are specifically designed for making grooves in most types of wood or several plastics. These router bits are finished with carbide cutting edges. Thanks to the carbide cutting edges, the router bit delivers high quality results for all your projects and a long working life.
This router bit can be used to work on most wood types or plastics. Thanks to the high quality finish of the bit, it is also possible to make grooves on different plastics such as acrylics (plexiglass), polycarbonate, polypropylene or PVC. To be used in router milling machines or CNC machines.
Works with all machines up to 7.5 KW. Connect several machines so that they can be started up together. Use this simultaneous starter when combining a woodworking machine and dust extractor. The starter motor ensures that your dust extraction system starts up automatically four seconds after you start up your woodworking machine yourself. After stopping your woodworking machine, extraction is also stopped a few seconds later. These extra few seconds of suction ensure that your pipes are always clean.
HD, the accessory for heavy work! For outdoor projects, solid railings and even wall frames. Size 14 coated screws ensure rock-solid connections. You need both the drill and the drill guide to get started.
This spare HD drill is for use on the Kreg Foreman machine and has a drilling diameter of 12 mm.
Ce coffret offre un grand nombre d'outils indispensables dont le professionnel a besoin pour démarrer avec sa machine combinée ou sa fraiseuse. L'ensemble se compose d'un porte outils de 50 mm de hauteur (art.3FR30935030). Ce porte outils multifonctionnelle convient à presque tous les couteaux à profiler actuellement disponibles sur le marché. Le porte outils peut porter aussi bien des couteaux profilés de 40 mm et 50 mm de hauteur que des couteaux remplaçables et des couteaux réversibles jusqu'à 50 mm. L'ensemble comprend trois couteaux de profil très pratiques qui vous permettent d'effectuer de nombreuses opérations. Cet ensemble comprend également trois autres porte outils: une fraise à rainurer réglable 5-9,5 mm de diamètre 120 mm (art.3FR3937120300510), comprenant un jeu de bagues de réglage, une fraise feuillurer et tenon 14-28 mm de diamètre 140 mm (3FR3928140301428), une fraise à profil plat-bande de diamètre 150 mm (art.3FR3947150301400).
Enfin, l'ensemble comprend également quelques accessoires utiles pour commencer à utiliser les différentes têtes de fraisage. Utilisez le reglet de toupilleur pour toujours régler correctement la profondeur et la hauteur de votre coupe. Le jeu (2) de sauterelles rapides verticales est en acier, équipé d'une poignée en PVC et d'un pied de pression en néoprène souple pour éviter d'endommager votre pièce de travail.
Saw blade with 42 teeth
Saw blade with alternate WZ top bevel teeth, suited for cutting across grain of soft wood, hard wood, aluminium-wood profiles or plastic-wood profiles. No noise saw blades for use on radial arm saws or table saws. Make sure to use the right amount of teeth to achieve optimal results of your project. A low number of teeth is suited for fast-paced and rough sawing.
Tuyau anti-statique longueur 3 mètre diamètre 100 mm. A utiliser en combinaison avec les extracteurs de poussière Air Flux.
Mèche de remplacement carrée Kreg #2 de 152 mm de long. Convient pour une utilisation avec les systèmes d'assemblage Kreg. Jeu de 2 pièces.
Porte outils d'une hauteur de 90 mm pour utilisation sur des fraiseuses à broche de 30 mm. Cette tête peut être utilisée avec tous nos couteaux de profil de hauteur 90 mm. Ces hauts profils sont principalement utilisés pour le fraisage des lambris, des corniches ou des profils de toit.
The length of this bit is 150mm
Slot mortising bits with chipbreaker, available with left or right hand rotation. These bits are well suited for drilling holes or grooves in most wood types. The bits have two cutting edges in 18% HSS steel and chip breakers.
Le servante à rouleau réglable supporte de grandes pièces jusqu’à 100 kg. Rouleau à roulement à billes chromé avec une base robuste. La base a quatre points pour niveler le support de rouleau. Il est rapide et facile à changer du rouleau au billes Réglage de la hauteur de 77 cm à 116 cm. Le support à rouleau peut être rapidement plié pour le stockage lorsqu'il n'est pas utilisé.
Set profielmessen hoogte 40mm Nr. 0024 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Deze elektrische vacuümtafel op kantelbare steun is ontworpen om gladde, niet poreuze werkstukken vast te klemmen. Het vacuüm tussen de basis van de tafel en het werkstuk zorgt voor een stevige klemming en laat na gebruik geen sporen na. Om de tafel vacuüm te maken dient ze aangesloten te zijn op het elektrische vacuümsysteem SVE600 van Virutex (standaard inbegrepen). Dankzij het compacte formaat is deze vacuümtafel zowel geschikt om in het atelier te gebruiken als daarbuiten. De kop van de steun kan 90° kantelen zodat u het werkstuk in een ideale positie kan plaatsen. Daarbovenop is de bovenplaat 360° draaibaar. De steun moet vastgezet worden met klemmen (niet inbegrepen). Omdat u de tafel zowel verticaal als horizontaal kan plaatsen is deze module ideaal voor een brede waaier aan toepassingen. Klem werkstukken vast om te verlijmen, frezen, trimmen, etc...
Met behulp van de standaard geleverd rubber dichtingen verdeelt u de tafel eenvoudig in kleinere secties. Dit is erg handig om bijvoorbeeld kleine stukken vast te zetten. Om grotere werkstukken vast te zetten is de optionele hulpsteun SVE680 beschikbaar. Deze steun is specifiek ontworpen om aan te sluiten op het model SVE660 of SVE670. Standaardlevering met één rubber dichting al geïnstalleerd.
The Belmash clamping devices provide increased safety when working with your thicknessing machine. Safely plane beams or boards on any Belmash machine. The pusher ensures that the workpiece is clamped to the work surface. This facilitates the flow of material, giving you a clean and precise finish. These clamping devices are easy to install using the screws and washers. The opening can be adjusted by means of a handle on the top and the spring clip on the side. In this way, a good supply and pressure force is always assured.
This pusher is suitable to be used on the Belmash SDM2500.
Spare knife with adjustable diameter 30mm-45mm for the adjustable hinge boring bit of Sistemi Klein (SKU: KL-R110600R).
Set profielmessen hoogte 40mm Nr. 0017 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Straight router bits are specifically designed for making grooves in most types of wood or several plastics. These router bits are finished with carbide cutting edges. Thanks to the carbide cutting edges, the router bit delivers high quality results for all your projects and a long working life.
This router bit can be used to work on most wood types or plastics. Thanks to the high quality finish of the bit, it is also possible to make grooves on different plastics such as acrylics (plexiglass), polycarbonate, polypropylene or PVC. To be used in router milling machines or CNC machines.
This 1 HP scoring unit is available as an option with the combination machines TT32K5SL, TT320K5 Massif and TT400K5 Massif.
Jeu de 5 outils PowerGrip incontournables pour le tournage sur bois. Fabriqué en acier HSS (18 %).
Ceci est le kit de démarrage idéal pour chacun qui veut commencer avec le tournage sur bois.
Le jeu est composé comme suit: gouge à dégrossir (largeur 19 mm) - gouge à profiler (largeur 13 mm) - bédane (largeur 10 mm) - grain d'orge (largeur 13 mm) - gouge à creuser (largeur 10 mm).
Saw blade with 56 teeth
Wolf tooth saw blade for classic machines, suitable for fast cutting of different types of wood, wet wood or brush wood. To be used on yard or construction machinery but mainly suitable for firewood saws. The entire saw blade is finished in high quality Chrome-vanadium steel. Made in Germany, take advantage of the extremely solid German quality. Easy to sharpen yourself.
Deux mousses EVA de remplacement haute densité pour le PushPRO. Les caoutchoucs sont réversibles, ils peuvent donc être utilisés deux fois.
À utiliser uniquement sur un bâton PushPRO (vendu séparément).
A set of ten high quality spacers with a tolerance of 0.01. The thicknesses vary between 1mm and 40mm with a total height of 130mm for all spacers together. These rings are available with bore 30mm (Ø45mm) or with bore 50mm (Ø70mm).
Verstekmeter van de extra topklasse. Fijn instelbare flip-stop, ingefreesde standaardhoeken, uitschuifbare aanslagverlenging
Als u op zoek bent naar accessoires voor uw zaagtafel of freestafel uit de categorie "compromisloos", dan heeft u die zojuist gevonden!
De ITAMAC Xact 36 hoort qua instelbaarheid, precisie, stabiliteit en afwerking zeker thuis in de "non-plus-ultraklasse". Absoluut ongeëvenaarde verstekmeter!
Set profielmessen hoogte 40mm Nr. 0000 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Lame de scie à 32 dents
Lame de scie avec denture alternée, brise-copeaux et conception anti-kickback. Avec peu de dents pour une coupe grossière et rapide du bois. Equipée de dents en carbure de haute qualité (widia). Convient pour la coupe de bois dur et tendre. Peut également être utilisé pour le sciage de panneaux d'aggloméré ou de bois collé sur une face. Idéal pour les scies de chantier ou les scies circulaires à chevalet. Made in Germany, profitez de la solide qualité allemande.
Cette table à vide électrique est conçue pour serrer des pièces lisses et non poreuses. Le vide entre la base de la table et la pièce à usiner assure un serrage ferme et ne laisse aucune trace après utilisation. Pour que la table soit à vide, elle doit être connectée au système de fixation électrique à vide SVE600 de Virutex (non intégré). Grâce à sa taille compacte, cette table à vide peut être utilisée aussi bien dans l'atelier qu'à l'extérieur. La table elle-même doit être fixée à l'aide de vis dans les trous prévus à cet effet. Comme vous pouvez placer la table à la fois verticalement et horizontalement, ce module est idéal pour un large éventail d'applications. Pièces de serrage pour le collage, le fraisage, l'ébavurage, etc...
En utilisant les joints en caoutchouc fournis en standard, vous pouvez facilement diviser le tableau en sections plus petites. C'est très utile pour sécuriser les petites pièces, par exemple. Pour sécuriser les grandes pièces, vous pouvez utiliser plusieurs modules pour éviter qu'elles ne s'affaissent. Livraison standard avec un joint en caoutchouc déjà installé.
Robuuste en volledig stalen wipzaag om snel, eenvoudig én veilig brandhout te verzagen. Deze brandhoutwipzaag is volledig conform de CEN-veiligheidsnormen voor dit type machines. Inclusief nulspanningsbeveiliging op de schakelaar voor verbeterde veiligheid bij spanningsverlies. Dankzij de afdekkap kan u tijdens het werken niet in de buurt van het zaagblad komen zodat het risico op ongevallen sterk vermindert. Deze wipzaagmachine is voorzien van een zaagblad in hoogwaardig hardmetaal (widia) met diameter Ø700mm. Dit model is voorzien van een driepuntsophanging en aansluiting voor cardanas. De machine kan zo aangedreven worden door een tractor. Overbrenging op het zaagblad met riemaandrijving. Uiterst geschikt voor het kappen van takken of boomstammen met een maximumdikte van 240mm.
De wipzaag is voorzien van een automatische terugkeereenheid met behulp van een veer. Het zaagblad is moeiteloos te bedienen en snijdt snel door het hout. Verzaag probleemloos en ergonomisch grote hoeveelheden hout in één keer. Met behulp van de verlengbare steun en maataanduiding verzaagt u zelfs langere stukken steeds op dezelfde maat. Voorzien van een stevige basis met twee wielen en een trekstang waardoor u de machine eenvoudig verplaatst. Probleemloos te verrijden, zowel binnen als buiten op oneffen ondergrond. Koppel deze wipzaag aan uw tractor om hem overal direct te kunnen inzetten. Volledig gemonteerd bij levering en klaar voor gebruik.
The BOW Portable Saw Featherboard features an innovative use of high-density EVA Foam/foam combs and clamping system that increases input control, dramatically improves recoil and better protects your wood from damage. This compared to the general plastic feaherboards. EVA is a high density, closed cell material with long life that you don't have with the common plastic featherboards. The springs are also unbreakable and, unlike plastic springs, they can be replaced if damaged.
Mounting material included.
Set profielmessen hoogte 40mm Nr. 0050 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
Gabarit robuste et de haute qualité pour le fraisage de joints à queue d'aronde à placer sur un établi. Grâce à son cadre robuste et fermé, la stabilité de cette unité est inégalée. Standard équipé d'un peigne avec un pas de 26 mm. Utilisez ce moule avec un douille de copiage de Ø19mm, inclus en standard avec votre défonceuse Virutex ou vendu séparément. Des peignes avec un pas de 16 mm ou 34 mm sont disponibles en option. Ils sont proposés sous la forme d'ensembles tout-en-un pratiques avec la bonne fraise et la bonne douille de copiage.
Si vous utilisez une fraise droite, vous pouvez également utiliser ce moule pour réaliser des assemblages à broches droites. Note : Il n'est pas possible de fraiser les queues d'aronde ou les stylos sans utiliser une bague de copie. Le douille de copiage pour pas de 26 mm et le fraise approprié (fraise à queue d'aronde art. 6040050 ou fraise droit art. 1140060) sont tous deux disponibles séparément.
Ce gabarit peut serrer les deux pièces de votre joint à queue d'aronde afin que le joint puisse être fraisé avec une précision de 100 %. Le moule est compatible avec les défonceuses Virutex suivants : FR66P, FR160P, FRE160P FR227R, FR278R, FRE317VD ou AS93. Votre défonceuse se déplace de manière parfaitement stable le long du gabarit, ce qui vous permet de fraiser les queues d'aronde en un seul passage. Grâce au peigne en PVC, votre fraise en carbure de tungstène ne risque pas d'être endommagée.
De TT2010 is een compacte, veelzijdige schuurmachine. Ze bevat een schuurband van 2010 x 153 mm, heeft een contourtafel voor rondschuurwerk en is voorzien van een afzuigmond. De band kan zowel verticaal als horizontaal geplaatst worden. De aluminium werktafels kunnen allebei onder een hoek tot 45° gekanteld worden. Door haar onklopbare prijs-kwaliteitverhouding is dit het ideale model voor vakmensen. De grafietcoating op de schuurtafel zorgt voor een beter glijvermogen van de schuurband.
Ze is standaard uitgerust met een scherm voor horizontaal schuren, een verstekaanslag en een quick-releasesysteem dat u in staat stelt om snel de schuurband te wisselen. Standaard wordt ook een onderstel meegeleverd.
De schuurband is verkrijgbaar in korrel 60, 80, 100 en 150.
Set profielmessen hoogte 40mm Nr. 0008 voor universele veiligheidsmessenkoppen. Geschikt voor het profielfrezen van massief houten kanten met heel lage gereedschapskosten. Gelegeerd gereedschapsstaal met 16% cobalt voor een hoge snijkwaliteit en snijcomfort.
This multifunctional position guide easily replaces all other guides or moulds. The T multi guide is an indispensable tool for making furniture, cabinets,... The high-precision drill guide allows you to carry out all drillings with a distance of 32mm (or more) correctly. Use this guide for: handles on doors and slides, holes for shelves, hinges or drawer guides. As an option, you can also use an extension piece to drill longer driving holes with a distance of 32mm. These extensions are available separately per set of two.
The guide has a central borehole and two adjustable boreholes in hardened steel. The basic length for this guide is 320mm. This can be extended up to 810mm with the optional extensions. Standard delivery with a Ø5mm drill bit.
The length of this bit is 140mm
Slot mortising bits with chipbreaker, available with left or right hand rotation. These bits are well suited for drilling holes or grooves in most wood types. The bits have two cutting edges in 18% HSS steel and chip breakers.
Capot en PVC noir avec tube à diamètre 100mm à utiliser avec les systèmes d'aspiration Air Flux. La taille de l’ouverture du capot anti-poussière est de 415x325mm.
Template to be used on the Virutex FR129VB Router for door hinges to mill Argenta Invisible Large. This template is only suitable for the model Invisible Large van Argenta. Other models available. Hinge not included.
Pièce de réduction à 4 pièces jusqu'à 100mm à utiliser avec les modèles differents des aspirateurs Air Flux.
Les scies à table HW110E de Steel City ont déjà prouvé qu'elles étaient l'une des tables de scie de la plus haute qualité dans le monde entier, avec plus de 30 000 clients satisfaits. Les scies à table se caractérisent par une conception et une ingénierie de pointe, un châssis robuste et un système d'entraînement puissant. Apparence et finition rayonnantes, précision et stabilité exceptionnelles, fonctionnement souple et fonctionnalités conviviales. Cette série comprend une table de sciage classique 3PK inclinable à gauche avec un système avancé de changement de coin de fendage ou une table de sciage à logement en queue d'aronde 5,5PK à usage intensif pour les coupes industrielles. Tous ces modèles sont équipés pour être utilisés avec le système Dado (lames de scie à rainures réglables pour couper les rainure et entre autres).
Transformez n'importe quelle perceuse en perceuse à 90° avec le tournevis pour trous de poche à 90° de Kreg. Avec cet accessoire compact pour perceuse, vous pouvez serrer des vis dans des endroits où vous ne pouvez pas les atteindre avec votre perceuse.
La mèche carrée de 7,62 cm fournie est dotée d'une pointe magnétique qui s'enclenche dans la tête d'une vis à trou de poche. Cet accessoire est d'application universelle, c'est-à-dire qu'il convient à toutes les perceuses et à tous les embouts hexagonaux. Grâce à sa conception ergonomique, vous pouvez facilement tenir le tourne-pièce 90° Kreg d'une main tout en utilisant la perceuse de l'autre. Il peut également être utilisé avec une perceuse à percussion. Lorsque vous devez serrer des vis dans des espaces restreints, vous pouvez compter sur le tourneur de trous de poche à 90° de Kreg pour faire le travail.
Deze boortafel van Belmash is compatibel met de SDM2500 machine. De boortafel kan worden geïnstalleerd in plaats van de freestafel. De boortafel kan volledig in hoogte en links/rechts geregeld worden. Inclusief twee klemmen die zorgen voor fixatie van het werkstuk.
De hoekmeter 'Angle Copy' van Virutex zorgt altijd voor de juiste hoek zonder hoeken te moeten bereken of uitmeten. Druk eenvoudig de Angle Copy in de hoek waarin u werkt en het toestel kopieert deze. Met behulp van een knop kan u de gekiopeerde hoek vastzetten zodat steeds de correcte hoek verzaagt. Zowel te gebruiken in binnen- als buitenhoeken. Dankzij de gradenboog kan u de Angle Copy ook gebruiken om handmatig hoeken aan te duiden op uw werkstuk.
The Kreg Pocket-Hole Jig 520 Pro is a practical and versatile jointing system. This system allows you to create very solid pocket holes in materials with a minimum thickness of 13 mm and a maximum thickness of 38 mm.
The Pocket-Hole Jig 520 Pro has a number of unique points. For example, the jig has a 360° rotatable handle. This handle ensures that you can comfortably use the system on any project. In addition, the Pocket-Hole Jig 520 Pro has a built-in clamping system. You simply squeeze the handle until the material is clamped firmly enough. The non-slip material on the 520 Pro ensures that the jointing system will not shift, no matter what position you use the jig in.
You can measure the thickness of the material with the supplied material thickness gauge. The measurements on the gauge correspond to those on the drilling jig and EasySet drill bit. You slide the stop collar to the correct size using the material thickness gauge, which is also a hex wrench. This adjustable stop collar ensures repeat accuracy of the Kreg jointing system. By setting the stop collar once, you can thus make several pocket holes in succession in the same material thickness.
The built-in clamping system provides more repeat accuracy as well. The handle has a quick-reset function, which ensures that the clamp remains at approximately the same thickness. This allows you to work with material of the same thickness several times in a row, without having to squeeze the handle several times.
The Kreg Pocket-Hole Jig 520 Pro comes with no less than 100 pocket hole screws and a step-by-step project plan. The Kreg jointing system also comes with a 51 mm Kreg quick-release clamp, for clamping and assembling your workpiece.
Cette fraise à rayon creux permet d'arrondir facilement et rapidement les coins pour obtenir une forme ronde. La fraise peut également être utilisée pour créer une rainure à fond plat entre deux formes rondes. En augmentant la profondeur de travail, vous obtenez le classique "quart de rond" qui est typique pour les bords des tables à manger, par exemple. Grâce à ses tranchants en carbure de haute qualité (widia), cette fraise peut être utilisée sur la plupart des types de bois.
Weight
0,65 kg
0,5 kg
0,05 kg
1 kg
0,05 kg
2 kg
0,5 kg
2 kg
N/B
0,05 kg
1 kg
0,05 kg
1 kg
0,05 kg
0,05 kg
0,05 kg
0,05 kg
N/B
5 kg
272 kg
0,05 kg
0,05 kg
0,05 kg
0,05 kg
1 kg
0,05 kg
220 kg
0,05 kg
0,5 kg
1,5 kg
0,05 kg
16,5 kg
0,05 kg
0,05 kg
0,05 kg
0,05 kg
0,500 kg
2,7 kg
7 kg
0,5 kg
0,75 kg
0,05 kg
0,05 kg
1 kg
1 kg
0,5 kg
0,05 kg
5 kg
0,05 kg
2 kg
0,05 kg
200 kg
0,300 kg
0,5 kg
0,325 kg
1 kg
2 kg
0,5 kg
0,05 kg
0,05 kg
1 kg
N/B
1 kg
2 kg
0,05 kg
0,05 kg
3 kg
0,05 kg
0,05 kg
1 kg
0,05 kg
0,35 kg
0,05 kg
0,5 kg
1 kg
0,01 kg
0,05 kg
1 kg
0,2 kg
2 kg
1 kg
1 kg
0,1 kg
1 kg
0,05 kg
7 kg
0,05 kg
1 kg
3 kg
0,05 kg
0,05 kg
0,05 kg
10 kg
N/B
1 kg
0,2 kg
0,05 kg
4 kg
0,05 kg
1 kg
0,325 kg
130 kg
0,3 kg
0,05 kg
6,2 kg
86 kg
0,05 kg
0,35 kg
0,05 kg
1 kg
0,1 kg
0,5 kg
240 kg
N/B
9,7 kg
0,5 kg
2 kg
0,05 kg
Dimensions
N/B
63 cm
N/B
N/B
N/B
N/B
N/B
N/B
N/B
0,4 cm
N/B
0,5 cm
N/B
0,4 cm
0,4 cm
0,4 cm
N/B
N/B
N/B
115,5 × 52,5 × 95,5 cm
N/B
N/B
N/B
0,4 cm
N/B
N/B
N/B
N/B
N/B
N/B
0,4 cm
N/B
0,4 cm
0,4 cm
N/B
N/B
380 cm
N/B
N/B
N/B
N/B
0,5 cm
0,5 cm
600 cm
N/B
N/B
N/B
N/B
0,5 cm
N/B
N/B
N/B
10,7 × 10 cm
N/B
16 × 20 × 2,2 cm
N/B
50 cm
N/B
N/B
0,5 cm
N/B
N/B
N/B
N/B
0,5 cm
N/B
N/B
N/B
N/B
N/B
N/B
320 × 215 cm
N/B
N/B
N/B
N/B
N/B
N/B
N/B
N/B
N/B
N/B
N/B
9 cm
N/B
30 cm
0,4 cm
N/B
30 × 26 × 7 cm
N/B
0,4 cm
N/B
N/B
N/B
N/B
N/B
N/B
50 cm
0,4 cm
N/B
16 × 20 × 2,2 cm
105 × 85 × 110 cm
N/B
0,4 cm
36 cm
1150 × 600 × 1100 cm
0,4 cm
320 × 215 cm
N/B
41,5 × 32,5 cm
N/B
N/B
N/B
N/B
34 × 18,5 cm
N/B
N/B
N/B
Additional information
Gewicht
0,65 kg
Max. Draagkracht
70kg
Paneeldikte
0-46mm
Gewicht
0,5 kg
Afmetingen
63 cm
Gewicht
0,05 kg
Diameter
24,7mm
Snijlengte
12mm
Lengte
51mm
Radius
R6
Schacht
8mm
Snijvlakken
2
Gewicht
1 kg
Stuks in verpakking
260
Materiaal
Zinc, Blue Kote
Gewicht
0,05 kg
Diameter
22,7mm
Snijlengte
12mm
Lengte
51mm
Radius
R5
Schacht
8mm
Snijvlakken
2
Gewicht
2 kg
Gewicht
0,5 kg
Gewicht
2 kg
Breedte lijmrol onderaan
122mm, 180mm
Breedte lijmrol bovenaan
92mm
Inhoud lijmbak
1kg, 1,4kg
Gewicht
0,05 kg
Afmetingen
0,4 cm
Gewicht
1 kg
Zaagblad diameter
125mm, 150mm, 180mm
As diameter
30mm
Tand dikte
8,0mm
Zaagblad dikte
6,0mm
Aantal tanden
12, 18, 24
Gewicht
0,05 kg
Afmetingen
0,5 cm
Gewicht
1 kg
Zaagblad diameter
400mm
As diameter
30mm
Tand dikte
3,5mm
Aantal tanden
36
Gewicht
0,05 kg
Afmetingen
0,4 cm
Gewicht
0,05 kg
Afmetingen
0,4 cm
Gewicht
0,05 kg
Afmetingen
0,4 cm
Gewicht
0,05 kg
Diameter
19mm
Snijlengte
19mm
Lengte
60mm
Hoek
7°
Snijvlakken
2
Schacht
8mm
Diameter
50mm, 100mm
Gewicht
5 kg
Gewicht
272 kg
Afmetingen
115,5 × 52,5 × 95,5 cm
Motor
4 PK, 5 PK
Voltage
230 V, 3 x 400V
Schaafbreedte
310 mm
Schaaftafel afmetingen
1380x310mm
Ø schaafas
70mm
Nominale snelheid schaafas
4800rpm
Aantal schaafmessen
3
Schaafmes afmetingen
310x19x1mm
Max. schaafdiepte
4mm
Vandiktetafel afmetingen
540x306mm
Doorlaathoogte vandikte
225mm
Vandikte afname
3mm
Aanvoersnelheid vandikte
6m/min
Gewicht
0,05 kg
Diameter
4mm
Snijlengte
11mm
Lengte
51mm
Snijvlakken
2+1
Gewicht
0,05 kg
Diameter
20mm
Snijlengte
32mm
Lengte
73mm
Schacht
12mm
Snijvlakken
2
Gewicht
0,05 kg
Diameter
9,5mm
Snijlengte
25mm
Lengte
67mm
Snijvlakken
2
Gewicht
0,05 kg
Afmetingen
0,4 cm
Gewicht
1 kg
Gewicht
0,05 kg
Diameter
6mm
Snijlengte
19mm, 25mm
Lengte
51mm, 57mm
Snijvlakken
2+1
Gewicht
220 kg
Motor
3 PK
Voltage
230 V
As diameter
30mm
Nominale snelheid
4.000rpm, 6.000rpm, 8.000rpm, 10.000rpm
Freesopening
38mm, 70mm, 100mm, 140mm
Freeshoogte
100mm
Werktafel
556x716mm, 220x716mm
Geleider
400x120mm
Aansluiting afzuiging
100 mm
Werkhoogte
860mm
Chassis
590x530mm
Verstekgeleider
-60° – +60°
Gewicht
0,05 kg
Diameter
14mm
Snijlengte
19mm
Lengte
51mm
Snijvlakken
2+1
Gewicht
0,5 kg
Lengte
3607mm
Breedte
13mm, 16mm, 20mm
Dikte
0,65mm, 0,80mm
Gewicht
1,5 kg
Vermogen
180W
Schuuroppervlakte
93x185mm
Ø Rotatie
2mm
Nominale snelheid
12500rpm
Trillingen
25000/min
Gewicht
0,05 kg
Afmetingen
0,4 cm
Gewicht
16,5 kg
Vandikte capaciteit
5-103mm
Aantal messen
2
Schaafbreedte
250 mm
Gewicht
0,05 kg
Afmetingen
0,4 cm
Gewicht
0,05 kg
Afmetingen
0,4 cm
Gewicht
0,05 kg
Korrel
K40, K60, K80, K100, K120, K150
Gewicht
0,05 kg
Diameter
20mm
As diameter
12,7mm
Gewicht
0,500 kg
Afmetingen
380 cm
Breedte lemmet
10 mm
Nuttige lengte lemmet
160 mm
Gewicht
2,7 kg
Boor diameter min/max
5-12 mm
Boordiepte
0-38 mm
Kantelbare geleider
0-90°
Motor
900 W
Gewicht
7 kg
Gewicht
0,5 kg
Diameter
100mm
Gewicht
0,75 kg
Temperatuur
1: 300°C, 2: 525°C
Luchtstroom
400l/min
Gewicht
0,05 kg
Afmetingen
0,5 cm
Gewicht
0,05 kg
Afmetingen
0,5 cm
Gewicht
1 kg
Afmetingen
600 cm
Diameter
100mm
Gewicht
1 kg
Diameter
150mm
As diameter
30mm, 50mm
Snijvlakken
2
Freeshoogte
36mm
Toerental Min-Max
5000-9500, 5100-8800
Gewicht
0,5 kg
Gewicht
0,05 kg
Diameter
12mm
Snijlengte
10mm
Lengte
50mm
Radius
R5
Snijvlakken
2
Gewicht
5 kg
Draagkracht
100kg
Tafel afmetingen
600x450mm
Hoogtes tafel
383mm, 621mm, 734mm, 810mm
Gewicht
0,05 kg
Afmetingen
0,5 cm
Gewicht
2 kg
Gewicht
0,05 kg
Diameter
12mm
Snijlengte
19mm, 25mm, 32mm
Lengte
51mm, 57mm, 63mm
Snijvlakken
2
Gewicht
200 kg
Gewicht
0,300 kg
Afmetingen
10,7 × 10 cm
Gewicht
0,3 kg
Gewicht
0,5 kg
Diameter
60mm, 100mm
Gewicht
0,325 kg
Afmetingen
16 × 20 × 2,2 cm
Afmetingen werkvlak
150x150mm
Vacuumkracht
800gr/cm² bij 6 bar
Werkdruk
5,5-7 bar
Luchtverbruik bij 5,5 bar
28l/min
Gewicht
1 kg
Diameter
78mm
As diameter
30mm
Freeshoogte
40mm
Gewicht
2 kg
Afmetingen
50 cm
Gewicht
0,5 kg
Lengte
3345mm
Breedte
6mm
Dikte
0,65mm
Gewicht
0,05 kg
Diameter
55mm
Lengte
90mm
Schacht
10x60mm
Gewicht
0,05 kg
Afmetingen
0,5 cm
Gewicht
1 kg
Afmetingen werkvlak
150x150mm
Vacuumkracht
800gr/cm² bij 6 bar
Werkdruk
5,5-7 bar
Luchtverbruik bij 5,5 bar
28l/min
Gewicht
N/B
Aantal stuks
100 pieces, 200 pieces, 500 pieces
Gewicht
1 kg
Gewicht
2 kg
As diameter
30mm
Gewicht
0,05 kg
Afmetingen
0,5 cm
Gewicht
0,05 kg
Diameter
9,5mm
As diameter
4,8mm
Dikte
3,2mm
Gewicht
3 kg
Schacht boor
6,35 mm
Boordiameter
9,5 mm
Min. materiaaldikte
13 mm
Max. materiaaldikte
38 mm
Gewicht
0,05 kg
Diameter
18mm
Snijlengte
19mm
Lengte
51mm
Snijvlakken
2+1
Gewicht
0,05 kg
Diameter
28mm
Lengte
90mm
Schacht
10x60mm
Gewicht
1 kg
Zaagblad diameter
350mm
As diameter
30mm
Tand dikte
1,8mm
Aantal tanden
56
Gewicht
0,05 kg
Diameter
3mm
Snijlengte
11mm
Lengte
51mm
Snijvlakken
2+1
Gewicht
0,35 kg
Afmetingen
320 × 215 cm
Gewicht
0,05 kg
Diameter
36,7mm
Snijlengte
20mm
Lengte
67mm
Radius
R12
Schacht
12mm
Snijvlakken
2
Gewicht
0,5 kg
Gewicht
1 kg
Gewicht
0,01 kg
Diameter
6mm, 8mm, 10mm, 12mm, 14mm, 16mm, 18mm
Schacht
15,9 mm
Gewicht
0,05 kg
Diameter
8mm
Snijlengte
25mm
Lengte
70mm
Schacht
12mm
Snijvlakken
2
Gewicht
1 kg
Gewicht
0,2 kg
Gewicht
2 kg
As diameter
30mm
Gewicht
1 kg
Zaagblad diameter
350mm
As diameter
30mm
Tand dikte
4,4mm
Zaagblad dikte
2,8mm
Aantal tanden
36
Gewicht
1 kg
Diameter
100mm
Gewicht
0,1 kg
Lengte
152 mm
Magnetische top
Oui
Maat
#2
Gewicht
1 kg
Afmetingen
9 cm
Diameter
100mm
As diameter
30mm
Freeshoogte
100mm
Gewicht
0,05 kg
Diameter
15mm
Lengte
150mm
Schacht
13x50mm
Draairichting
Links, Rechts
Gewicht
7 kg
Afmetingen
30 cm
Laad capaciteit
100kg
Gewicht
0,05 kg
Afmetingen
0,4 cm
Gewicht
1 kg
Vermogen
95W
Afmetingen werkvlak
150x150mm
Vacuümdruk
750mbar
Gewicht
3 kg
Afmetingen
30 × 26 × 7 cm
Max. hoogte werkstuk
63mm
Max. breedte werkstuk
270mm
Gewicht
0,05 kg
Diameter
30-45mm
Gewicht
0,05 kg
Afmetingen
0,4 cm
Gewicht
0,05 kg
Diameter
16mm
Snijlengte
32mm
Lengte
73mm
Schacht
12mm
Snijvlakken
2
Gewicht
10 kg
Zaagblad diameter
150mm
Motor
1 PK
Gewicht
1 kg
Zaagblad diameter
400mm
As diameter
30mm
Tand dikte
2,0mm
Aantal tanden
56
Gewicht
0,2 kg
Gewicht
0,05 kg
As diameter
30mm, 50mm
Diameter
45mm, 70mm
Gewicht
4 kg
Afmetingen
50 cm
Hoekbereik
+/- 60°
Vaste verstekken
-60°, -45°, -22,5°, 0°, 22,5°, 45°, 60°
Geleiderprofiel
460 x 19 x 9 mm
Nauwkeurigheid fijnafstelling
0,02 mm
Gewicht
0,05 kg
Afmetingen
0,4 cm
Gewicht
1 kg
Zaagblad diameter
350mm
As diameter
30mm
Tand dikte
3,5mm
Aantal tanden
32
Gewicht
0,325 kg
Afmetingen
16 × 20 × 2,2 cm
Vermogen
95W
Afmetingen werkvlak
150x150mm
Vacuümdruk
750mbar
Gewicht
130 kg
Afmetingen
105 × 85 × 110 cm
Motor
7 PK
Zaagblad diameter
700mm
Max. Snijdiameter
240mm
Gewicht
0,3 kg
Gewicht
0,05 kg
Afmetingen
0,4 cm
Gewicht
6,2 kg
Afmetingen
36 cm
Tandafstand
26mm
Min - Max houtdikte
11mm – 30mm
Gewicht
86 kg
Afmetingen
1150 × 600 × 1100 cm
Kanteling
45°
Korrel
K60, K80, K100, K150
Werktafel
514 x 221 mm, 790 x 221 mm
Schuurband
2010 x 152 mm
Motor
2 PK
Voltage
230 V
Gewicht
0,05 kg
Afmetingen
0,4 cm
Gewicht
0,35 kg
Afmetingen
320 × 215 cm
Gewicht
0,05 kg
Diameter
13mm
Lengte
140mm
Schacht
16x50mm
Draairichting
Links, Rechts
Gewicht
1 kg
Afmetingen
41,5 × 32,5 cm
Diameter
100mm
Gewicht
0,1 kg
Gewicht
0,5 kg
Gewicht
240 kg
Voltage
230 V
Motor
3 PK
Zaagblad diameter
250mm
Zaagdiepte 45°
50mm
Zaagdiepte 90°
70mm
Toerental zaagblad
4150
Max. breedte DADO
15mm
Aansluiting afzuiging
100 mm
Max. breedte links zaagblad
305 mm
Max. breedte rechts zaagblad
750 mm
T-slots
2
Werkhoogte
860mm
Werktafel
508 x 685mm
Gewicht
9,7 kg
Afmetingen
34 × 18,5 cm
Gewicht
0,5 kg
Gewicht
2 kg
Schacht boor
6.35 mm
Boordiameter
9.5 mm
Min. materiaaldikte
13 mm
Max. materiaaldikte
38 mm
Gewicht
0,05 kg
Diameter
8mm
Snijlengte
10mm
Lengte
50mm
Radius
R3
Snijvlakken
2
Meld je aan voor onze nieuwsbrief
Select the fields to be shown. Others will be hidden. Drag and drop to rearrange the order.
Image
SKU
Rating
Price
Stock
Availability
Add to cart
Description
Content
Weight
Dimensions
Additional information
Click outside to hide the comparison bar
Vergelijken
We gebruiken cookies om ervoor te zorgen dat onze website zo soepel mogelijk draait. Als je doorgaat met het gebruiken van de website, gaan we er vanuit dat je ermee instemt.OkPrivacy policy